Statics › Section J · Moments of inertia › Topic J.3

The parallel axis theorem

Tables give moments of inertia about a shape's own centroid, but real problems need them about some other axis. The parallel axis theorem makes that shift with one extra term, and it also explains why the material far from the axis matters most.

The problem of the moving axis

The previous topic found formulas such as \(bh^3/12\) for a rectangle about its centroid. In a real cross-section, though, each piece sits somewhere away from the axis you care about: the flange of a beam is well above the beam's centroid, and a hole in a plate is off to one side. Integrating again for every new axis would be slow. The parallel axis theorem avoids it. If you know a shape's centroidal moment of inertia about one direction, you can shift to any other axis in that direction using just two more numbers: its area and the distance between the axes.

Where the theorem comes from

Let the \(x'\) axis pass through the centroid and let a parallel x axis lie a distance \(d\) away. A piece of area at height \(y'\) above the centroidal axis is at \(y = y' + d\) from the x axis. Then

I_x = \int_A (y' + d)^2\,dA = \int_A y'^2\,dA + 2d\int_A y'\,dA + d^2\int_A dA

The first integral is the centroidal value \(\bar{I}\). The last is the area \(A\). The middle one is the first moment about a centroidal axis, which is zero, as the topic Integral properties of shapes showed. What remains is the theorem:

I = \bar{I} + Ad^2

Using the theorem

You need three things: the centroidal moment of inertia \(\bar{I}\) for the right direction, the area \(A\), and the perpendicular distance \(d\) from the centroid to the new axis. The two axes must be parallel. Because \(Ad^2\) can never be negative, the centroidal axis gives the smallest moment of inertia of all the axes in that direction, and every other parallel axis gives more. You can also run the theorem backwards, \(\bar{I} = I - Ad^2\), to find a centroidal value from one about another axis. A quick check of both directions: for a rectangle about its base, \(d = h/2\) and

\frac{bh^3}{12} + bh\left(\frac{h}{2}\right)^2 = \frac{bh^3}{3}

Worked example: a triangle's centroidal value

A triangle has \(I = bh^3/12\) about its base. Find its centroidal moment of inertia about an axis parallel to the base. 1. The centroid of a triangle is a third of the way up, so \(d = h/3\), as the topic Centroids showed. 2. The area is \(A = bh/2\). 3. Run the theorem backwards:

\bar{I} = \frac{bh^3}{12} - \frac{bh}{2}\left(\frac{h}{3}\right)^2 = \frac{bh^3}{12} - \frac{bh^3}{18} = \frac{bh^3}{36}

4. Check with numbers: a triangle with \(b = 90\) mm and \(h = 60\) mm has \(1.62 \times 10^6\ \mathrm{mm^4}\) about its base and \(0.54 \times 10^6\ \mathrm{mm^4}\) about its centroid, smaller as it must be.

Worked example: an offset tube

A tube of outer radius 40 mm and inner radius 25 mm has its centre 100 mm from the y axis. Find its moment of inertia about the y axis. 1. Centroidal value:

\bar{I} = \frac{\pi}{4}(40^4 - 25^4) = 1.704 \times 10^6\ \mathrm{mm^4}

2. Area: \(A = \pi(40^2 - 25^2) = 3063\ \mathrm{mm^2}\). 3. Transfer term: \(Ad^2 = 3063 \times 100^2\), which is \(30.63 \times 10^6\ \mathrm{mm^4}\). 4. Total: \(I_y = 32.3 \times 10^6\ \mathrm{mm^4}\). Check: the transfer term is about 18 times the tube's own value. Moving area away from an axis raises its moment of inertia far more than its shape does.

Semicircles and quarter circles

The same backward step gives the centroidal values the previous topic could not. A semicircle of radius \(r\) has \(\pi r^4/8\) about its diameter, area \(\pi r^2/2\), and its centroid \(4r/(3\pi)\) from the diameter. So, about the parallel centroidal axis,

\bar{I}_x = \left(\frac{\pi}{8} - \frac{8}{9\pi}\right)r^4 \approx 0.1098\,r^4

About its axis of symmetry, which already passes through the centroid, it keeps \(\pi r^4/8\). A quarter circle is half a semicircle in each direction, so about either centroidal axis parallel to a straight edge,

\bar{I} = \left(\frac{\pi}{16} - \frac{4}{9\pi}\right)r^4 \approx 0.0549\,r^4

A table of centroidal values

For a rectangle \(b\) wide and \(h\) tall, the centroid is at the centre and \(\bar{I}_x = bh^3/12\), \(\bar{I}_y = hb^3/12\). For a triangle of base \(b\) and height \(h\), the centroid is \(h/3\) above the base and \(\bar{I}_x = bh^3/36\). For a circle of radius \(r\), \(\bar{I} = \pi r^4/4\) about any diameter. For a semicircle, the centroid is \(4r/(3\pi)\) from the diameter, with \(\bar{I} \approx 0.1098\,r^4\) parallel to it and \(\pi r^4/8\) about the symmetry axis. For a quarter circle, the centroid is \(4r/(3\pi)\) from each straight edge, with \(\bar{I} \approx 0.0549\,r^4\) in both directions. Add \(Ad^2\) for any other parallel axis.

Worked example: between two off-centre axes

The 90 mm by 60 mm triangle from earlier has \(1.62 \times 10^6\ \mathrm{mm^4}\) about its base. Find its moment of inertia about a parallel axis through its apex, 60 mm above the base. 1. The theorem only starts from the centroid, so first step down to it: \(\bar{I} = 0.54 \times 10^6\ \mathrm{mm^4}\). 2. The apex is \(2h/3 = 40\) mm from the centroid, and \(A = 2700\ \mathrm{mm^2}\). 3. Step up:

I = 0.54 \times 10^6 + 2700 \times 40^2 = 4.86 \times 10^6\ \mathrm{mm^4}

4. Check: in symbols this is \(bh^3/4\). Adding \(A \times 60^2\) straight to the base value would give \(11.3 \times 10^6\ \mathrm{mm^4}\), more than twice too big.

Why the flanges carry a beam

The theorem explains the shape of an I-beam. Picture a flange plate 150 mm wide and 20 mm thick whose centroid is 110 mm from the beam's centroidal axis. Its own centroidal value is \(150 \times 20^3/12 = 0.10 \times 10^6\ \mathrm{mm^4}\), but its transfer term is \(3000 \times 110^2 = 36.3 \times 10^6\ \mathrm{mm^4}\), over 99% of the total. Material placed far from the axis is worth far more than material near it, so an I-beam puts most of its steel in two flanges and joins them with a thin web. The physics topic Rotational dynamics and moment of inertia used the mass version, \(I = I_{\text{cm}} + Md^2\), in kg·m², for a rod pivoted at one end.

Common mistakes to avoid

First, transferring between two axes that are not centroidal in one step: go down to the centroid, then up. Second, measuring \(d\) to the edge of the shape instead of to its centroid. Third, subtracting \(Ad^2\) when moving away from the centroid, or adding it when moving towards it. Fourth, using axes that are not parallel; the theorem only shifts an axis sideways. Fifth, forgetting the shape's own \(\bar{I}\) and keeping only \(Ad^2\), which is close for thin flanges but wrong for deep parts. Sixth, mixing an area moment in \(\mathrm{mm^4}\) with a mass moment in kg·m².

Key takeaways

The parallel axis theorem is I = Ī + Ad², where Ī is about a centroidal axis, A is the area, and d is the perpendicular distance between the two parallel axes. It comes from the first moment about a centroidal axis being zero. The centroidal axis gives the smallest I for its direction. Run backwards, Ī = I − Ad², it gives a triangle Ī = bh³/36, a semicircle about 0.1098 r⁴ and a quarter circle about 0.0549 r⁴. Between two off-centre axes, always pass through the centroid. Area far from the axis dominates through the Ad² term, which is why beams have flanges.

Flashcards

Flashcard

I = Ī + Ad²

Parallel axis theorem for area moments of inertia

Ī is about the centroidal axis; d is the distance between the parallel axes.

Test your understanding

Question 1 of 5

A rectangle 40 mm wide and 90 mm tall has a horizontal axis 60 mm below its base. What is its moment of inertia about that axis?

Question 2 of 5

Why is the centroidal moment of inertia the smallest of all moments of inertia about parallel axes?

Question 3 of 5

A triangle has I = bh³/12 about its base, area bh/2, and centroid h/3 above the base. What is its centroidal moment of inertia about an axis parallel to the base?

Question 4 of 5

A section of area 2000 mm² has I = 3.0 × 10⁶ mm⁴ about an axis 30 mm from its centroid. What is I about a parallel axis 50 mm from the centroid?

Question 5 of 5

A semicircle has radius 60 mm. What is its moment of inertia about the centroidal axis parallel to its diameter?

← Previous topicNext topic →