Statics › Section I · Friction › Topic I.1
Dry friction
Until now, most contacts in this course have been treated as smooth. Real surfaces grip, and that grip decides whether a crate stays put, a wedge holds or a belt slips, so this topic builds the friction model that the rest of the section depends on.
Friction in statics
Friction is the force that resists relative sliding between surfaces in contact. Engineers meet several kinds: rolling resistance at a wheel, fluid friction inside a moving liquid, drag on a body moving through air or water, and internal friction in a deforming material. Statics deals with only one, dry friction between solid surfaces, also called Coulomb friction. Earlier sections treated most contacts as smooth, carrying only a normal force. A rough contact can also carry a force parallel to the surface, and that changes how blocks, wedges, screws, belts, bearings and discs behave.
The Coulomb model
Guillaume Amontons published rules for friction in 1699, and Charles-Augustin de Coulomb tested and extended them in 1781; Leonardo da Vinci had recorded similar observations around 1500 in notebooks published much later. Their model says the limiting friction force is proportional to the normal force \(N\), the contact force perpendicular to the surfaces, and is roughly independent of the apparent contact area. The constant of proportionality, the coefficient of friction \(\mu\), is a measured property of one pair of surfaces in one condition: dry, oily, rusty or polished. It has no units and is usually below 1. Every coefficient in this section is a given value for its problem, not a universal constant; the physics topic "Friction" lists typical ranges.
Static friction has a ceiling
While the surfaces do not slip, the friction force \(F\) is static friction, and it takes whatever value equilibrium demands, up to a limit:
Push a heavy cabinet gently and friction matches your push exactly. The limit is reached at impending motion, the instant just before slipping, when \(F = \mu_s N\), and only then. Problem statements signal it with words such as "about to slip", "maximum" or "minimum". Friction always points in the direction that opposes the relative slip that would occur without it.
Kinetic friction and constant velocity
Once slipping starts, the force drops to kinetic friction, \(F = \mu_k N\), where the kinetic coefficient \(\mu_k\) is usually smaller than \(\mu_s\). A body that accelerates is outside statics, but a body sliding at constant velocity has zero acceleration and is in equilibrium, so the same equations apply. A 30 kg skid dragged across a yard at constant speed by a rope pulling 120 N at 30° above the horizontal has \(N = 294.3 - 60 = 234.3\) N and \(F = 120\cos 30^\circ = 103.9\) N, so \(\mu_k = 103.9/234.3 = 0.44\).
Friction angle and friction resultant
The friction and normal forces at a contact are perpendicular, so they combine into one friction resultant \(R = \sqrt{F^2 + N^2}\), tilted away from the normal by an angle \(\phi\) with \(\tan\phi = F/N\). As friction grows, \(\phi\) grows, until at impending motion it reaches the friction angle \(\phi_s\):
The reaction at a rough contact can therefore lean anywhere inside a cone of half-angle \(\phi_s\) about the normal, and never outside it. A block on a slowly tilted plank starts to slip when the plank angle reaches \(\phi_s\), because the weight is then the only other force and the resultant must lie along it. The same idea underlies the angle of repose of piled gravel.
Where the normal force acts
The normal force is really spread over the whole contact face, and so is the friction. In two-dimensional problems each distribution is replaced by one concentrated force, as in the topic "Distributed loads". The resultant normal force does not stay at the centre of the face. On a box at rest with no push, it sits directly below the centre of gravity. A sideways push above the floor and the friction at floor level form a turning effect, so the normal force shifts toward the leading edge to restore moment equilibrium, and further as the push grows. The next topic uses this shift to decide whether a box slides or tips.
Three kinds of problem
Dry-friction problems come in three types. Static but not impending: the body is at rest and nothing says it is about to move, so \(F\) is an unknown found from equilibrium. Impending motion: set \(F = \mu_s N\) at each contact about to slip, which supplies the extra equation for a maximum or minimum. Steady sliding: set \(F = \mu_k N\). When unsure, assume equilibrium, solve for the friction needed and compare. If it is no larger than \(\mu_s N\), the assumption holds; otherwise the body slips and the friction becomes \(\mu_k N\).
Worked example: does the crate move?
A 60 kg crate sits on a level floor with \(\mu_s = 0.40\). A worker pushes on it with 250 N directed 25° below the horizontal. Does it move? 1. Weight: \(W = 60 \times 9.81 = 588.6\) N. 2. Vertical equilibrium, assuming no motion, the push adds \(250\sin 25^\circ = 105.7\) N downward, so \(N = 588.6 + 105.7 = 694.3\) N. 3. Friction available: \(\mu_s N = 0.40 \times 694.3 = 277.7\) N. 4. Friction needed: the horizontal part of the push, \(250\cos 25^\circ = 226.6\) N. 5. Since 226.6 N is less than 277.7 N, the crate stays put, and the friction is exactly 226.6 N, not 277.7 N. 6. Contrast: a 250 N horizontal push would leave only 235.4 N of friction available, so the crate would slide. Pushing downward raises the normal force and the available friction.
Worked example: a crate on a ramp
A 150 kg crate rests on a ramp inclined at 20°, with \(\mu_s = 0.25\). Find the range of pushes \(P\), parallel to the ramp, that keep it at rest. 1. \(W = 1471.5\) N, with components \(W\sin 20^\circ = 503.3\) N down the slope and \(N = W\cos 20^\circ = 1382.8\) N into it. 2. Maximum friction: \(0.25 \times 1382.8 = 345.7\) N. 3. Impending motion up the slope, so friction acts down it: \(P = 503.3 + 345.7 = 849.0\) N. 4. Impending motion down the slope, so friction acts up it: \(P = 503.3 - 345.7 = 157.6\) N. 5. The crate stays at rest for any push from 157.6 N to 849.0 N. 6. Check: \(\tan 20^\circ = 0.364\) exceeds 0.25, so with no push the crate would slide down, which agrees with a positive minimum.
Common mistakes to avoid
First, writing \(F = \mu_s N\) for every body at rest: that is only the ceiling, reached at impending motion. Second, taking \(N = mg\) without a free-body diagram; slopes and angled pushes change \(N\), as both crate examples showed. Third, drawing friction in an arbitrary direction at impending motion. Its direction is fixed by the slip it opposes, and a wrong guess gives a wrong answer rather than just a negative sign. Fourth, using \(\mu_s\) for a body that is already sliding. Fifth, treating a coefficient as exact: measured values vary with surface condition, so designs allow a margin.
Key takeaways
Statics models dry, or Coulomb, friction between solid surfaces. Static friction takes whatever value equilibrium needs, up to μs N, a limit reached only at impending motion; steady sliding gives μk N, usually smaller. Coefficients are measured for a given pair of surfaces and conditions. The friction and normal forces combine into a resultant tilted from the normal by at most the friction angle, where tan φs = μs. The normal force's line of action shifts as the loads change. Classify each problem as static, impending or sliding, and when unsure, solve for the friction needed and compare it with μs N.
Flashcards
Flashcard
Friction between two solid surfaces in contact
Test your understanding
Question 1 of 5
A 40 kg box rests on a level floor with μs = 0.50. A horizontal push of 150 N is applied. What is the friction force on the box? Use g = 9.81 m/s².
Question 2 of 5
A block rests on a plank with μs = 0.70 between them. The plank is slowly tilted. At about what angle does the block start to slip?
Question 3 of 5
A 50 kg sled is pulled across level snow at constant velocity by a rope with 160 N of tension, angled 20° above the horizontal. What is μk? Use g = 9.81 m/s².
Question 4 of 5
A 100 kg crate rests on a 25° ramp with μs = 0.30. What push, parallel to the ramp, puts it on the point of moving up the slope? Use g = 9.81 m/s².
Question 5 of 5
A box sits at rest on a rough floor while a small sideways push acts on it. Which statement about the static friction force is correct?
