Statics › Section E · Rigid body equilibrium › Topic E.3
Equations of equilibrium
A rigid body stays still only if its forces balance and its moments balance too. Two vector equations hold the whole of statics, and knowing how they break into scalar equations, and which sets of them are independent, is what makes problems solvable.
Why forces alone are not enough
Grip a steering wheel with both hands and push up with your right hand while pulling down equally hard with your left. The two forces add to zero, yet the wheel turns. For a particle, a zero force sum was the whole condition for equilibrium, because a point cannot rotate. A rigid body can, and a pair of equal and opposite forces that do not share a line of action, a couple, spins it without moving it anywhere. So a rigid body needs a second condition: the moments must balance as well as the forces.
What equilibrium means
Newton's second law says a net force produces linear acceleration, and its rotational counterpart says a net moment produces angular acceleration. Statics deals with bodies that have neither: no linear acceleration \(\mathbf{a}\) and no angular acceleration \(\boldsymbol{\alpha}\). Most are at rest, though a body moving in a straight line at constant speed without rotating is in equilibrium too. Setting both accelerations to zero gives the two conditions:
Every force and every couple acting on the body, applied loads and support reactions alike, must be included in these sums.
Six scalar equations
Each vector equation holds three scalar equations, one for each axis:
That makes six, one for each degree of freedom of a rigid body in space. The force equations stop translation along each axis, and the moment equations stop rotation about each axis. Particles need only the first three, which is why particle problems never called for moments.
The planar set
When every force lies in the xy plane, three of the six equations take care of themselves. No force has a z component, so \(\sum F_z = 0\) automatically, and a force in the plane can only turn the body about an axis perpendicular to the plane, so \(\sum M_x\) and \(\sum M_y\) are zero too. What remains is the standard 2D set:
Here \(M_A\) means the moment about the z axis through any chosen point A in the plane. Three equations match the three degrees of freedom of a planar body.
Any point will do
Why may A be any point? If the forces balance, the moment sum is the same about every point. For two points A and B,
where \(\mathbf{r}_{BA}\) runs from B to A. With \(\sum \mathbf{F} = \mathbf{0}\), the last term vanishes, so a zero moment about one point means a zero moment about all of them. This freedom is a powerful tool. Take moments about a point where two unknown forces act, and both drop out of that equation, leaving one unknown to find directly.
Worked example: a simply supported beam
An 8 m beam is pinned at its left end A and rests on a roller at its right end B. It carries a 15 kN downward load 3 m from A; ignore its weight. 1. Free-body diagram: \(A_x\) and \(A_y\) at the pin, an upward \(B_y\) at the roller and the 15 kN load. Three unknowns. 2. \(\sum F_x = 0\) gives \(A_x = 0\), as there is no other horizontal force. 3. Moments about A, counterclockwise positive: \(8B_y - 15(3) = 0\), so \(B_y = 5.625\) kN. 4. \(\sum F_y = 0\): \(A_y = 15 - 5.625 = 9.375\) kN. 5. Check with moments about B: \(-8(9.375) + 15(5) = 0\). The support nearer the load carries more of it.
Worked example: a cantilever with a couple
A horizontal 3 m beam is built into a wall at its left end A. It carries a 4 kN downward load at its free end B and a clockwise couple of 5 kN·m applied at its midpoint. 1. Free-body diagram: the fixed support gives \(A_x\), \(A_y\) and a couple \(M_A\), drawn counterclockwise. 2. \(\sum F_x = 0\): \(A_x = 0\). 3. \(\sum F_y = 0\): \(A_y = 4\) kN upward. 4. Moments about A: \(M_A - 4(3) - 5 = 0\), so \(M_A = 17\) kN·m counterclockwise. 5. Check about B: \(17 - 4(3) - 5 = 0\). The couple enters as \(-5\) in both moment equations, because a couple has the same moment about every point.
Other valid sets
The standard set is not the only choice. Either force equation can be swapped for a second moment equation, and both can be swapped for two. The set \(\sum F_x = 0\), \(\sum M_A = 0\), \(\sum M_B = 0\) works provided the line AB is not perpendicular to the x axis. Three moment equations about A, B and C work provided the three points are not on one straight line. The conditions matter. A single unbalanced force whose line of action passes through A and B would pass both moment tests. If AB were perpendicular to x, that force would have no x component either, and the set would miss it entirely.
Independent equations and checks
You can write a moment equation about as many points as you like, but a planar body never gives more than three independent equations. Any further equation is a combination of the first three, which makes it an ideal check, as in both worked examples. It also sets a hard limit. A single planar body can have at most three unknown reactions found by statics, and a body in space at most six. Problems that break this limit are the subject of "Stability and determinacy".
Signs and units
This course counts counterclockwise moments as positive; whatever you choose, keep it throughout an equation. A force's moment is its size times its perpendicular distance from the point. A couple is added as it stands, with no distance needed. Moments carry units of force times length, N·m or kN·m in SI and lb·ft or kip·ft in US customary units. A negative answer for a reaction does not mean a mistake; it means that reaction acts opposite to the direction you assumed on the free-body diagram.
Common mistakes to avoid
First, writing only force equations for a rigid body and missing the rotation condition. Second, dropping a couple from a moment equation, or multiplying it by a distance as though it were a force. Third, mixing sign conventions within one moment sum. Fourth, writing a fourth equation for a planar body and expecting it to find a fourth unknown; it will only repeat information. Fifth, choosing three moment points on one line, or two moment points on a line perpendicular to the force direction used, which makes the set fail.
Key takeaways
A rigid body is in equilibrium when \(\sum \mathbf{F} = \mathbf{0}\) and \(\sum \mathbf{M} = \mathbf{0}\): no linear or angular acceleration. In space these give six scalar equations; in a plane they reduce to \(\sum F_x = 0\), \(\sum F_y = 0\) and \(\sum M_A = 0\). If the forces balance, the moment sum is the same about every point, so choose a point that removes unknowns. Valid alternatives use two or three moment equations, with conditions on the points. A planar body has only three independent equations; extras are checks.
Flashcards
Flashcard
ΣF = 0 and ΣM = 0
Test your understanding
Question 1 of 5
Two equal and opposite forces act on a rigid body along different parallel lines. Which statement is true?
Question 2 of 5
A 10 m beam is pinned at A and on a roller at B, its right end. A 20 kN load acts 4 m from A. What is the reaction at B?
Question 3 of 5
A 2.5 m cantilever carries 6 kN downward at its free end. What couple must the fixed support supply?
Question 4 of 5
How many independent equilibrium equations can be written for a single rigid body loaded in a plane?
Question 5 of 5
Which set of three equations can fail to guarantee equilibrium of a planar body?
