Statics › Section E · Rigid body equilibrium › Topic E.2

Supports, reactions, and free-body diagrams

Every support holds a body by pushing or pulling back in the directions it blocks. Learning exactly what each support can supply, and drawing it correctly on a free-body diagram, is the most important step in every equilibrium problem.

Replacing supports with forces

A beam does not know it is sitting on a roller or bolted to a wall; it only feels the forces and couples those supports exert. So the first job in any rigid-body problem is to remove each support and replace it with what it can supply. The rule follows from the topic "Degrees of freedom": a support gives a reaction force in every direction in which it prevents translation, and a reaction couple about every axis about which it prevents rotation. If it allows a motion, it supplies nothing in that direction.

Five steps to a free-body diagram

1. Isolate the body: sketch it alone, free of everything that touches it, never on top of the original picture. 2. Draw a right-handed coordinate system, ideally lined up with unknown forces. 3. Add every applied load and couple, including the body's weight if it is not negligible. 4. Work round the outline and, wherever a support was removed, draw the reactions it supplies. 5. Label every force, couple, dimension and angle with a value or a symbol, so the diagram stands on its own.

Supports that give one unknown

A smooth surface, roller or rocker stops motion only perpendicular to the surface, so it supplies one normal force. A pin running in a smooth slot, or a collar pinned to a body and sliding on a smooth rod, gives one force perpendicular to the slot or rod. A cable gives one tension force along the cable, pulling away from the body. A weightless link pinned at both ends, or a spring, gives one force along its line, in tension or compression. Bridges often rest on rollers at one end so the deck can expand and contract with temperature.

Supports that give two or three

A smooth pin or hinge stops a point translating in any direction in the plane but lets the body turn. It supplies two force components, \(A_x\) and \(A_y\), or equivalently one force of unknown size and direction; door hinges work this way. A rough surface supplies a normal force and a friction force. A collar locked against turning on a smooth rod gives a normal force and a couple. A fixed support, such as a beam built into a wall or a diving board clamped at one end, stops all motion and supplies \(A_x\), \(A_y\) and a couple \(M_A\).

The 2D supports at a glance

One unknown: a roller, rocker or smooth surface (a normal force); a pin in a slot or a collar on a rod (a force normal to the slot or rod); a cable (a tension, away from the body); a link or spring (a force along its line). Two unknowns: a pin or hinge (\(A_x\) and \(A_y\)); a rough surface (a normal force and friction); a locked collar on a rod (a normal force and a couple). Three unknowns: a fixed support (\(A_x\), \(A_y\) and \(M_A\)). For each of these idealised supports, the number of unknowns equals the number of motions it blocks.

Directions and senses

When a reaction has a known line of action, as at a roller, cable or link, draw it along that line as one unknown magnitude, not as two components. If its sense is not obvious, guess. A negative answer later simply means the force acts the other way. The exceptions are one-way supports. A cable can only pull, so a negative tension means the cable would go slack; a body simply resting on a surface can only be pushed, so a negative normal force means it would lift off. Either way, the model must change.

Worked example: a diving board

A uniform horizontal diving board 3.5 m long weighs 350 N. It is pinned at its back end A and rests on a roller at B, 1.0 m from A, so 2.5 m of board overhangs B. A diver weighing 650 N stands at the far tip. Draw its free-body diagram. 1. Sketch the board alone, with x to the right and y up. 2. Applied loads: 350 N down at the midpoint, 1.75 m from A, and 650 N down at the tip, 3.5 m from A. 3. The pin at A becomes two unknowns, \(A_x\) and \(A_y\). 4. The roller at B becomes one vertical unknown, \(B\), drawn upward. 5. Check: three unknowns and three equilibrium equations, so the reactions can be found, as the topic "2D rigid body equilibrium" does.

Worked example: a shelf on a cable

A horizontal beam AB, 2.4 m long and weighing 200 N, is pinned to a wall at A. A cable runs from B to a point C on the wall 1.8 m above A. A 500 N box sits 1.6 m from A. 1. Isolate the beam, x along it, y up. 2. Loads: 200 N down at 1.2 m from A and 500 N down at 1.6 m. 3. The pin at A gives \(A_x\) and \(A_y\). 4. The cable gives one tension \(T\) at B, pointing from B towards C. Its run is 2.4 m horizontally and 1.8 m vertically, so it is 3.0 m long and makes \(\tan^{-1}(1.8/2.4) = 36.9^\circ\) with the beam. 5. Check: three unknowns, \(A_x\), \(A_y\) and \(T\), as a solvable problem needs.

Supports in 3D

In space a body has six possible motions. A smooth surface or a cable still gives one force. A ball-and-socket joint stops all translation but allows free turning: three force components. A journal bearing, in which a shaft can slide and spin, gives two forces and two couples perpendicular to the shaft: four unknowns. A thrust bearing or a hinge also stops sliding, adding an axial force: five. A square shaft in a square bearing can slide but not spin, giving two forces and three couples: five. A fixed support gives three forces and three couples: six.

Available and engaged reactions

A reaction that turns out non-zero is engaged; one that could act but is not needed is available but not engaged. A crate on a floor with a slack cable tied to its top is held up by the floor alone; remove the floor and the cable engages. Hold a heavy book level in one hand and your hand supplies a force and a couple. Add your other hand and the couple fades, because two separated forces now do its job. So a shaft in two aligned bearings, or a door on two hinges, is usually modelled with forces only.

Common mistakes to avoid

First, leaving out a reaction, most often the couple at a fixed support or the horizontal force at a pin. Second, adding reactions a support cannot supply, such as a couple at a pin. Third, drawing a cable pushing on the body; cables only pull. Fourth, splitting a force whose line of action is known into two independent unknowns. Fifth, forgetting the body's own weight, or drawing forces between parts of the same body, which cancel and never belong on its diagram.

Key takeaways

Isolate the body, add axes and loads, replace each support with its reactions, and label everything. A support gives a force for each translation it blocks and a couple for each rotation it blocks. In 2D, rollers, smooth surfaces, cables and links give one unknown; pins and rough surfaces give two; a fixed support gives three. In 3D, a ball and socket gives three, a journal bearing four, a hinge or thrust bearing five and a fixed support six. Guess unknown senses freely; a negative answer reverses them.

Flashcards

Flashcard

Support rule

A force for each blocked translation, a couple for each blocked rotation

Allowed motions get no reaction.

Test your understanding

Question 1 of 5

How many unknown reactions does a fixed support give a body in 2D?

Question 2 of 5

A beam rests on a smooth roller on a horizontal floor at B. Which reaction belongs at B on its free-body diagram?

Question 3 of 5

In the shelf example, the cable from B rises 1.8 m over a horizontal run of 2.4 m. What angle does it make with the beam?

Question 4 of 5

Which 3D support gives three force components and no couples?

Question 5 of 5

After solving, the tension in a cable comes out as −120 N. What does this mean?

← Previous topicNext topic →