Statics › Section E · Rigid body equilibrium › Topic E.4

2D rigid body equilibrium

Beams, brackets and boards loaded in a plane are the everyday problems of statics. There are many correct ways to solve each one; this topic shows how to pick an efficient route and check that the answer is right.

Many routes, one answer

A planar rigid body has three equilibrium equations, and the previous topic showed there are several valid sets to choose from, any moment centre will do, and the axes can point any way you like. Every sound choice gives the same reactions in the end. What differs is the effort. A good choice gives three equations that each contain one unknown and can be solved on the spot. A poor one gives three equations tangled together, which means solving them simultaneously, the slowest and most error-prone path. Spending half a minute choosing well saves pages of algebra.

An efficient method

1. Draw a complete free-body diagram and count the unknowns: three, for a solvable single body. 2. Line the axes up with as many unknown forces as possible. 3. Sum moments about a spot that two unknown forces both pass through, often a pin, so that equation holds just one unknown. 4. Use the force equations, each now holding one unknown. 5. Check the results with an equation you have not used, usually moments about a second point. 6. Read the signs: a negative result means that reaction acts opposite to the arrow you drew.

Forces at an angle

Reactions with a known direction, such as a rocker on a sloping surface or an inclined cable, bring one unknown magnitude. Resolve it into components with trigonometry before writing the equations. A rocker resting on a surface sloped at \(30^\circ\) pushes perpendicular to that surface, so its reaction \(D\) is tilted \(30^\circ\) from the vertical, with components \(D\sin 30^\circ\) horizontally and \(D\cos 30^\circ\) vertically. To find the moment of an angled force, add the moments of its components, as the topic "Varignon's theorem" showed. A component whose line passes through the moment centre contributes nothing.

Worked example: the diving board

Solve the board from "Supports, reactions, and free-body diagrams": 3.5 m long, weight 350 N, pinned at its back end A, roller at B 1.0 m from A, and a 650 N diver at the tip. 1. Unknowns: \(A_x\), \(A_y\) and an upward \(B\). 2. No horizontal loads, so \(A_x = 0\). 3. Moments about A: \(1.0B - 350(1.75) - 650(3.5) = 0\), giving \(B = 2887.5\) N. 4. Vertical forces: \(A_y + 2887.5 - 1000 = 0\), so \(A_y = -1887.5\) N. 5. Check about B:

-1.0(-1887.5) - 350(0.75) - 650(2.5) = 0

The negative sign says the pin pulls the board down; without that pull the board would tip forward over the roller.

Uniform distributed loads

Many loads are spread out: the weight of a floor slab, snow on a roof or a beam's own weight. A uniform load of intensity \(w\), in force per unit length such as kN/m, acting over a length \(L\), can be replaced in the equilibrium equations by a single resultant force \(wL\) acting at the middle of the loaded length. By symmetry, the middle is the only place that gives the same moment as the spread-out load. Make this replacement before writing equations, but only for the whole body's equilibrium. The topic "Distributed loads" handles loads whose intensity varies along the beam.

Worked example: a beam with an overhang

A beam is pinned at A, rests on a roller at B 6 m to the right, and overhangs to a free end C, 2 m beyond B. A uniform load of 2 kN/m covers AB, and a 5 kN load hangs at C. 1. Replace the uniform load by \(2 \times 6 = 12\) kN at 3 m from A. 2. \(A_x = 0\), as nothing acts horizontally. 3. Moments about A: \(6B - 12(3) - 5(8) = 0\), so \(B = \frac{76}{6} \approx 12.67\) kN. 4. Vertical forces: \(A_y = 17 - 12.67 = 4.33\) kN. 5. Check about B: \(-6(4.33) + 12(3) - 5(2) \approx 0\). The overhang load reduces the reaction at A and increases the one at B.

Worked example: a sloped rocker and a couple

A horizontal 6 m beam AD is pinned at its left end A and rests at its right end D on a rocker whose surface slopes at \(30^\circ\), so the reaction \(D\) leans \(30^\circ\) from vertical, towards A. It carries 10 kN downward 2 m from A and a clockwise couple of 6 kN·m at its midpoint. 1. Unknowns: \(A_x\), \(A_y\), \(D\). 2. Moments about A, where \(D\)'s horizontal part has no arm: \(6D\cos 30^\circ - 10(2) - 6 = 0\), so \(D = 5.00\) kN. 3. Horizontal: \(A_x = D\sin 30^\circ = 2.50\) kN to the right. 4. Vertical: \(A_y = 10 - D\cos 30^\circ = 5.67\) kN. 5. Check about D: \(-6(5.67) + 10(4) - 6 \approx 0\). The pin force is \(\sqrt{2.50^2 + 5.67^2} = 6.19\) kN at \(66.2^\circ\) above the horizontal.

When equations couple

Sometimes no point removes two unknowns, or a poor choice of moment centres leaves every equation with two or three unknowns in it. The equations are still correct; they just have to be solved together. Write them in matrix form, \(A\mathbf{x} = \mathbf{b}\), with the unknown reactions in \(\mathbf{x}\), and let a calculator or software do the elimination. The answers match the one-at-a-time route exactly. This only works because the unknowns appear linearly: reactions are multiplied by known distances and known sines or cosines. If an angle itself is unknown, the equations are no longer linear and need a different approach.

Reading the answers

Three habits catch most errors. First, check signs against intuition: in a simply supported beam the support nearer a load carries more of it, and every downward load should be balanced by upward reactions summing to the same total. Second, run the independent check equation every time. A non-zero result means a moment arm, sign or component is wrong somewhere. Third, report results fully. Give each reaction's size and direction, and combine pin components into a single magnitude and angle when asked, as in the sloped-rocker example.

Common mistakes to avoid

First, taking moments about a point where no unknowns meet, which tangles the equations needlessly. Second, using the full length instead of the perpendicular distance for an angled force. Third, swapping sine and cosine when resolving a reaction that is tilted from the vertical rather than from the horizontal. Fourth, placing a distributed load's resultant at the end of the loaded length instead of its middle, or forgetting it acts only over that length. Fifth, treating a negative reaction as a mistake and flipping signs by hand, which hides any real error.

Key takeaways

Draw the free-body diagram, count three unknowns, and plan before calculating. Align axes with unknown forces, take moments about the point where two unknowns meet, then solve each force equation for its single unknown. Resolve angled forces into components and use perpendicular distances. Replace a uniform load \(w\) over length \(L\) by \(wL\) at the middle of that length. Check with an unused moment equation, read negative signs as reversed directions, and use matrix methods when the equations cannot be uncoupled.

Flashcards

Flashcard

Efficient solution

Three equations with one unknown each

Avoid simultaneous equations where you can.

Test your understanding

Question 1 of 5

A 3 m board, weight ignored, is pinned at its back end A and on a roller 1 m from A. A 600 N person stands at the tip. What does the pin exert?

Question 2 of 5

A 6 m simply supported beam carries 3 kN/m over its left 4 m only. What is the reaction at the right-hand support B?

Question 3 of 5

A rocker on a 30° slope gives a reaction of 8 kN, tilted 30° from vertical. What is its horizontal component?

Question 4 of 5

A beam has a pin at A and a roller at B. To find the roller force in one step, about which point should you take moments?

Question 5 of 5

A pin reaction drawn to the right comes out as Ax = −2.5 kN. What should you report?

← Previous topicNext topic →