Statics › Section I · Friction › Topic I.5
Flexible belts
Wrap a rope a few times round a post and one hand can hold a ship. The same friction that makes that possible lets belts drive machines and band brakes stop drums, and it grows exponentially with the angle of wrap.
Ropes, belts and drums
Whenever a flexible rope, cable or belt wraps around a curved surface, friction acts all along the arc of contact. Deck crews control a mooring line by taking turns around a bollard, a fixed post on the quay or deck. A motor drives a machine through a belt running over two pulleys. A band brake stops a rotating drum by tightening a band around it. On a smooth surface the contact can only push at right angles to the belt, so the tension is the same at both ends, as for the ideal pulleys of "1D equilibrium: cables, springs, and pulleys". Friction lets the two tensions differ, and the difference is what holds the load, transmits the moment or absorbs the energy. This topic finds how large it can be before the belt slips.
Which side is tighter?
With friction, call the larger tension \(T_2\) and the smaller \(T_1\). You must decide which side is which before calculating, because the formula below is exponential and a wrong choice cannot be repaired by a minus sign. Ask which way the belt would slip relative to the surface if friction vanished. Friction on the belt opposes that slip, so summing forces along the belt gives \(T_2 = T_1 +\) friction: the larger tension is on the side toward which the belt is about to slip. For a rope holding a hanging load over a post, the load side is tighter.
Deriving the belt equation
Take a tiny piece of belt spanning an angle \(d\theta\), with tension \(T\) at one end and \(T + dT\) at the other, on the point of slipping. Its two tensions point almost opposite each other, so their components toward the drum's centre add to about \(T\,d\theta\), and the normal force must balance them: \(dN = T\,d\theta\). Along the belt, the change in tension is balanced by friction at its limit: \(dT = \mu_s\,dN\). Eliminating \(dN\) gives \(\frac{dT}{T} = \mu_s\,d\theta\). Integrating over the whole contact angle \(\beta\) gives \(\ln(T_2/T_1) = \mu_s\beta\).
The capstan equation
Taking exponentials gives the belt friction equation:
It is often called the capstan equation or the Euler-Eytelwein formula. Here \(\beta\) is the contact angle in radians, one full turn being \(2\pi\). Use \(\mu_s\) when slipping is impending, and \(\mu_k\) when a rope slides round a fixed drum at constant speed. The drum's radius does not appear, as long as the belt touches it all along the arc. Because \(\beta\) sits in an exponent, each extra full turn multiplies the ratio by the same factor, \(e^{2\pi\mu}\). With \(\mu = 0.30\), one turn gives a ratio of 6.59, and three turns give about 286.
Worked example: a line on a bollard
A deckhand takes 2.5 turns of a mooring line around a fixed bollard, with \(\mu_s = 0.25\) between line and bollard, and holds the free end with 150 N. What is the largest pull from the ship that the line can resist without slipping? 1. The ship's side is about to pull the line round, so it carries \(T_2\), and the deckhand's end carries \(T_1 = 150\) N. 2. Contact angle: \(\beta = 2.5 \times 2\pi = 15.71\) rad. 3. Exponent: \(\mu_s\beta = 0.25 \times 15.71 = 3.927\), so the ratio is \(e^{3.927} = 50.8\). 4. \(T_2 = 150 \times 50.8 = 7610\) N, about 7.6 kN. 5. One more turn multiplies the ratio by \(e^{2\pi \times 0.25} = 4.81\), to 244, so 3.5 turns resist about 36.6 kN.
Contact angles in belt drives
In a belt drive, the belt leaves each pulley along a tangent, which is perpendicular to the radius at that point. For an open belt joining pulleys of radii \(r\) and \(R\) whose centres are a distance \(C\) apart, right-triangle geometry gives a small angle \(\psi\) with \(\sin\psi = (R - r)/C\). The belt wraps the smaller pulley through \(\beta = \pi - 2\psi\) and the larger through \(\beta = \pi + 2\psi\). If both contacts have the same coefficient, the smaller pulley has the smaller contact angle, so it is where the belt slips first. For other layouts, draw the radii to the tangent points and add up the angles.
Torque and power
The two tensions act tangentially at the pulley's rim, so the net moment they exert on a pulley of radius \(r\) is
The largest torque a drive can carry is reached when \(T_2\) hits \(T_1 e^{\mu\beta}\) at whichever pulley slips first. Both pulleys feel the same tension difference, so their torques are in the ratio of their radii. Power is torque times angular speed in radians per second, \(P = M\omega\). The larger pulley turns more slowly in the same ratio, so the power in and the power out are equal, ignoring losses.
Worked example: a motor belt drive
A motor pulley of radius 50 mm drives a pulley of radius 150 mm by a flat belt; the centres are 500 mm apart, \(\mu_s = 0.30\) on both pulleys, and the slack side carries 200 N. Find the largest torques and the power at 1450 rev/min. 1. \(\sin\psi = 0.10/0.50\), so \(\psi = 11.54^\circ\). 2. Small pulley: \(\beta = 180^\circ - 23.07^\circ = 156.9^\circ = 2.739\) rad, ratio \(e^{0.822} = 2.274\). The large pulley's ratio is 2.896, so the small one slips first. 3. \(T_2 = 200 \times 2.274 = 454.9\) N. 4. Torques: \(254.9 \times 0.050 = 12.7\) N·m at the motor and \(254.9 \times 0.150 = 38.2\) N·m at the driven pulley. 5. \(\omega = 1450 \times 2\pi/60 = 151.8\) rad/s, so \(P = 12.74 \times 151.8 = 1.93\) kW.
V-belts and band brakes
A V-belt sits in a groove with sloping sides at an included angle \(\alpha\). The groove walls wedge the belt, so the normal forces must be larger to give the same radial support, and the available friction rises with them:
For a 36° groove, the exponent is multiplied by \(1/\sin 18^\circ = 3.24\), so the drive above would reach a ratio of about 14.3 instead of 2.27. A band brake uses the flat-belt equation directly: a lever tightens a band round a drum, and a small pull on the slack end resists a much larger tension on the tight end.
Common mistakes to avoid
First, putting \(\beta\) in degrees or in turns; it must be in radians. Second, assigning \(T_2\) to the wrong side. Decide from the direction of impending slip before calculating. Third, multiplying when you should divide: the holding end is the smaller tension. Fourth, adding the friction as \(\mu\beta T\) instead of using the exponential, which badly underestimates rope friction. Fifth, using the larger pulley's contact angle to find when a drive slips. Sixth, using the equation when friction is below its limit; it gives the largest possible ratio, not the actual one.
Key takeaways
Friction along a wrapped belt lets the two tensions differ; without it they are equal. The larger tension T2 is on the side toward which the belt would slip, and it must be identified first. At impending slip, T2 = T1 e^(μβ), with β in radians, independent of the drum radius, so each extra turn multiplies the ratio by e^(2πμ). For open drives the small pulley wraps π − 2ψ, where sin ψ = (R − r)/C, and slips first. A pulley's torque is (T2 − T1) r and power is Mω. V-belts divide the exponent by sin(α/2); band brakes use the flat-belt equation.
Flashcards
Flashcard
Friction spread along the arc where a rope or belt wraps a surface
Test your understanding
Question 1 of 5
A rope makes one full turn around a fixed post, with μs = 0.30. A 2,000 N load hangs from one end. What is the smallest pull on the other end that stops the load from slipping down?
Question 2 of 5
A rope passes over a fixed rough rail with a load hanging on one end, and someone holds the other end so the load is about to slip down. Which end carries the larger tension?
Question 3 of 5
An open flat belt joins pulleys of radii 50 mm and 200 mm, with centres 600 mm apart. What is the contact angle on the smaller pulley?
Question 4 of 5
A flat belt wraps 2.8 rad of a 60 mm radius pulley, with μs = 0.35 and a slack-side tension of 150 N. What is the largest torque it can transmit to that pulley?
Question 5 of 5
A flat belt drive can reach a tension ratio of 2.0 before slipping. If it is replaced by a V-belt in a 40° groove, with the same μ and contact angle, what ratio can it reach?
