Statics › Section I · Friction › Topic I.6
Journal bearings
Every hinge, pivot pin and axle that turns in a plain hole fights friction. Statics can predict exactly how much moment that friction resists, using one neat geometric idea: the friction circle.
Shafts in plain bearings
A bearing supports a rotating shaft. Ball and roller bearings replace sliding with rolling, and oil-lubricated journal bearings float the shaft on a pressurised film; both need more than statics to analyse. This topic treats the simplest kind, a dry journal bearing: a shaft, or journal, turning inside a slightly larger cylindrical sleeve, touching it along one line. The bearing stops the shaft moving sideways but not along its axis. Because the surfaces rub directly, dry bearings wear and heat up, so they suit slow or occasional motion, such as door hinges, pivot pins in linkages and the axles of hand-operated pulleys. The aim is to find the moment that friction resists.
The shaft climbs the bearing
With no moment applied, a shaft carrying a downward load \(P\) rests at the very bottom of the bearing, and the contact force is a pure normal force straight up. Now apply a clockwise moment. At the bottom, the shaft's surface tries to move to the left, so friction on the shaft acts to the right, and the shaft rolls a little way up the right-hand side of the bearing, like a wheel climbing a curved ramp. It climbs until friction reaches its limit and the shaft starts to slip, then keeps turning at that position. A counterclockwise moment makes it climb the left-hand side instead. The contact point always moves opposite to the direction in which the shaft's surface slides there.
The friction circle
At the contact point, the normal force points along the radius toward the centre of the shaft, and friction acts along the tangent. Combine them into a single friction resultant \(R\), tilted from the normal by the friction angle \(\phi\). A line through the contact point at angle \(\phi\) to the radius passes the centre at a perpendicular distance
where \(r\) is the shaft radius. So the resultant is always tangent to a small circle of radius \(r_f\) centred on the shaft: the friction circle. Use \(\phi_s\) for a shaft about to start turning and \(\phi_k\), with \(\tan\phi_k = \mu_k\), for one turning steadily.
The moment friction resists
Taking moments about the shaft's centre, the normal force contributes nothing, because it passes through the centre. The whole friction moment therefore comes from the resultant acting at its offset:
If the shaft is driven by a pure couple, the only other force is the load, so \(R\) equals \(P\) and acts straight up, offset from the centre by \(r_f\). For small coefficients, \(\sin\phi \approx \tan\phi = \mu\), giving the handy estimate \(M \approx \mu R r\). The estimate is slightly high: for \(\mu = 0.20\) it overstates the moment by about 2%.
A method for bearing problems
1. Draw the shaft slightly smaller than the bearing so the contact point is clear, but treat the two radii as equal. 2. Decide which way the shaft turns, or is about to turn, relative to the bearing. 3. Draw the friction circle, radius \(r\sin\phi\), and place the resultant \(R\) tangent to it, on the side where its moment about the centre opposes the relative rotation. 4. Sketch the shaft's free-body diagram, including every applied load and \(R\), and solve the equilibrium equations. When the other loads are not vertical, the direction of \(R\) follows from force equilibrium, and the friction circle then fixes its line of action.
Worked example: a shaft under load
A shaft of diameter 60 mm turns steadily in a dry bearing that carries a radial load of 8.0 kN. The shaft is driven by a pure couple, and \(\mu_k = 0.20\). Find the moment needed to keep it turning. 1. Friction angle: \(\phi_k = \tan^{-1} 0.20 = 11.31^\circ\). 2. Friction circle: \(r_f = 30 \times \sin 11.31^\circ = 5.88\) mm. 3. The couple adds no force, so \(R = P = 8000\) N, acting upward and offset 5.88 mm from the centre on the side that opposes the rotation. 4. Moment: \(M = 8000 \times 0.00588 = 47.1\) N·m. 5. Check with the estimate: \(\mu_k P r = 0.20 \times 8000 \times 0.030 = 48.0\) N·m, about 2% higher, as expected. At 300 rev/min this friction would turn about 1.5 kW into heat, which is why dry bearings suit slow motion.
Fixed shaft, rotating hub
Many bearings are the other way round: the shaft is fixed and the part around it turns, as in a pulley spinning on a stationary axle or a wheel on a stub axle. The method is the same, but the free-body diagram is drawn for the rotating part, the hub, rather than for the axle. The axle pushes on the hub with a resultant tangent to the friction circle, whose radius uses the axle radius, not the radius of the pulley. Its offset from the centre is again on the side whose moment opposes the hub's rotation. For a pulley this means friction makes the pull needed to lift a load greater than the load itself, unlike the ideal pulley.
Worked example: a pulley on a fixed axle
A rope runs over a pulley of radius 100 mm that turns on a fixed axle of diameter 20 mm, with \(\mu_s = 0.25\) at the axle. Both rope ends hang vertically, and the pulley's weight is neglected. A 1500 N load, \(T_1\), hangs on the left. What pull \(T_2\) on the right starts to raise it? 1. Friction circle: \(\phi_s = 14.04^\circ\), so \(r_f = 10 \times \sin 14.04^\circ = 2.43\) mm. 2. The pulley is about to turn clockwise, so the axle's upward resultant, \(T_1 + T_2\), passes to the right of the centre, giving a counterclockwise moment. 3. Moments about the centre: \(T_2(100) = T_1(100) + (T_1 + T_2)(2.43)\). 4. Rearranging:
5. Check: lowering reverses the offset, giving \(1500 \times 0.9526 = 1429\) N, so the hand must hold back 1429 N while lowering and pull 1575 N while lifting.
Common mistakes to avoid
First, using the pulley's radius instead of the shaft or axle radius for the friction circle. Second, writing \(r_f = r\tan\phi\); the exact offset uses the sine, and the tangent form is only the small-angle estimate. Third, placing the resultant on the wrong side of the centre: its moment must oppose the relative rotation. Fourth, forgetting that a pulley's axle carries the sum of the two rope tensions, not just the load. Fifth, using \(\mu_s\) for a shaft already turning steadily.
Key takeaways
A dry journal bearing contacts its shaft along one line, and under a moment the shaft climbs the bearing until friction reaches its limit, so the contact point moves opposite to the surface slip. The friction and normal forces combine into one resultant tangent to the friction circle, of radius r sin φ, where r is the shaft or axle radius. The friction moment is R r sin φ, close to μ R r for small μ. Use φs at impending rotation and φk for steady turning. For a fixed axle and rotating hub, draw the hub's free-body diagram; friction makes lifting over a pulley cost more than the load.
Flashcards
Flashcard
The part of a shaft that turns inside a bearing sleeve
Test your understanding
Question 1 of 5
A dry journal bearing on a shaft of diameter 50 mm carries a radial load of 4.0 kN, and the shaft is driven by a pure couple, with μk = 0.25. What moment keeps it turning steadily?
Question 2 of 5
A loaded shaft in a dry journal bearing is made to turn clockwise. Where does the contact point between shaft and bearing settle?
Question 3 of 5
In a dry journal bearing at the point of slipping, what is true of the line of action of the friction resultant on the shaft?
Question 4 of 5
A rope over a pulley of radius 80 mm lifts a 1,000 N load, both ends vertical. The axle's friction circle has radius 2.0 mm. What pull starts to lift the load?
Question 5 of 5
For a small friction coefficient, which expression is a good estimate of the moment a dry journal bearing resists, where R is the resultant load and r the shaft radius?
