Statics › Section I · Friction › Topic I.4

Screw threads

A car jack lets one person lift the corner of a car, and a vice can crush wood with a turn of the handle. Both are screws: inclined planes wrapped into a helix, where friction decides how hard they are to turn and whether they hold their load on their own.

A wedge wrapped round a cylinder

A screw thread is a ridge of uniform shape that spirals around a cylinder. Unwrap one turn of it and you get a ramp, so a screw is an inclined plane, close kin to the wedge of the previous topic, but driven by a moment instead of a push. Screws that hold parts together are fasteners; screws that move loads are power screws, or lead screws, and they are the subject here. A power screw works with a nut carrying matching internal threads. In some machines the nut is fixed and the screw turns and travels through it, as in a C-clamp. In others the screw only turns and the nut travels along it, as in a scissor jack. Either way, a modest moment produces a large axial force at a precisely controlled position.

Handedness and the right-hand rule

Most threads are right-handed. Curl the fingers of your right hand in the direction a right-hand screw is turned, and your thumb points the way it advances. Looking at the head of an ordinary bolt, turning it clockwise drives it away from you and tightens it. Left-hand threads advance the opposite way and are used for good reasons. The left pedal of a bicycle has one, so that pedalling does not gradually unscrew it, and gas-welding equipment uses left-hand fittings for the fuel gas so that they cannot be confused with the right-hand oxygen fittings. Turning a screw end over does not change its handedness: a right-hand thread is right-handed from either end.

Thread geometry

This course analyses square threads only. Common V-shaped profiles, such as ISO metric threads, press on the nut at a slant, which acts like extra friction and makes them harder to analyse. Three dimensions matter. The mean radius \(r\) is measured from the axis to a point halfway between the crest and the root of the thread. The pitch is the distance between neighbouring threads, and the lead \(l\) is how far the screw advances in one turn. On a single-start thread they are equal, but a thread with \(n\) starts has \(l = n \times\) pitch. Unwrapping one turn gives a right triangle with base \(2\pi r\) and height \(l\), so the lead angle is

\alpha = \tan^{-1}\frac{l}{2\pi r}

Raising a load

Suppose an axial load \(W\) opposes the motion, as when a jack raises a car. Unwrap the thread into a ramp at angle \(\alpha\). The applied moment \(M\) acts on each small piece of thread like a horizontal push \(M/r\) at the mean radius, driving the load up the ramp. At impending motion the nut's reaction on the thread is a friction resultant tilted \(\phi_s\) from the normal, so it makes the angle \(\alpha + \phi_s\) with the axis. Summing over the whole thread, the axial components carry \(W\) and the tangential components balance \(M/r\), so

M = W r\tan(\alpha + \phi_s)

Both the ramp, through \(\alpha\), and the friction, through \(\phi_s\), add to the effort.

Lowering a load: three cases

When the load points the same way as the motion, as when a jack lowers a car, the result depends on comparing \(\phi_s\) with \(\alpha\). If \(\phi_s > \alpha\), the screw is self-locking: it holds the load with no moment, and lowering needs

M' = W r\tan(\phi_s - \alpha)

in the loosening direction. If \(\phi_s < \alpha\), the load turns the screw by itself, and a holding moment \(M'' = W r\tan(\alpha - \phi_s)\) in the raising direction keeps it at impending motion. If \(\phi_s = \alpha\), the screw is exactly on the verge and needs no moment, a borderline case with no margin. These formulas use \(\mu_s\) for impending motion; for steady turning, use the kinetic coefficient instead.

Worked example: a screw jack

A square-thread jack screw has a mean diameter of 30 mm and a single-start thread of pitch 6 mm, with \(\mu_s = 0.15\). It supports 12 kN and is turned by a 0.40 m handle. 1. Lead angle: \(\tan\alpha = \frac{6}{2\pi \times 15} = 0.0637\), so \(\alpha = 3.64^\circ\). 2. Friction angle: \(\phi_s = \tan^{-1} 0.15 = 8.53^\circ\). 3. Raising, with \(Wr = 12000 \times 0.015 = 180\) N·m: \(M = 180\tan 12.17^\circ = 38.8\) N·m, so the handle force is \(38.8/0.40 = 97\) N. 4. Since \(\phi_s > \alpha\), the jack is self-locking and holds the load by itself. 5. Lowering: \(M' = 180\tan 4.89^\circ = 15.4\) N·m, or 38 N at the handle. 6. Check: with no friction, raising would need \(Wl/2\pi = 11.5\) N·m, less than 38.8 N·m, as it must be.

Efficiency and the price of holding

In one turn, the moment does work \(2\pi M\) and the load rises by \(l\), gaining \(Wl\). The efficiency of raising is the ratio of the two:

\eta = \frac{Wl}{2\pi M} = \frac{\tan\alpha}{\tan(\alpha + \phi_s)}

For the jack, \(\eta = 0.0637/0.2157 = 0.295\), so under 30% of the handle's work lifts the car and the rest becomes heat. That is the price of self-locking. A square-thread screw that holds its load has \(\phi_s \ge \alpha\), and then its efficiency is always below 50%. A screw built for efficiency, with a steep lead or very low friction, will not hold its load on its own.

Worked example: a two-start lead screw

A square-thread lead screw on a machine slide has a mean diameter of 20 mm, a pitch of 5 mm and two starts, with \(\mu_s = 0.10\). It moves a 2.0 kN axial load. 1. Lead: \(l = 2 \times 5 = 10\) mm. 2. Lead angle: \(\alpha = \tan^{-1}\frac{10}{2\pi \times 10} = 9.04^\circ\), while \(\phi_s = \tan^{-1} 0.10 = 5.71^\circ\). 3. Driving against the load, with \(Wr = 20\) N·m: \(M = 20\tan 14.75^\circ = 5.27\) N·m. 4. Since \(\phi_s < \alpha\), the load would turn the screw backwards; holding it needs \(M'' = 20\tan 3.33^\circ = 1.16\) N·m. 5. Efficiency: \(\tan 9.04^\circ/\tan 14.75^\circ = 0.60\). 6. Check: a single-start version would have \(\alpha = 4.55^\circ\), below \(\phi_s\), and would be self-locking. Ball screws push this further, with friction so low that they usually need a brake to hold a load.

Common mistakes to avoid

First, confusing lead with pitch on a multi-start thread; the lead angle depends on the lead. Second, putting the diameter where the mean radius belongs, in \(2\pi r\) or in \(Wr\). Third, using \(\tan(\alpha + \phi_s)\) for lowering a self-locking screw; lowering uses the difference of the angles. Fourth, calling a screw self-locking without comparing \(\phi_s\) with \(\alpha\). Fifth, applying square-thread formulas to V-threads, which behave as if friction were higher.

Key takeaways

A screw is an inclined plane wrapped into a helix and driven by a moment. Right-hand threads advance in the direction of the right thumb when turned the way the fingers curl. The lead is the advance per turn, equal to the number of starts times the pitch, and the lead angle is α = tan⁻¹(l/2πr) at the mean radius. Raising a load needs M = W r tan(α + φs). If φs > α the screw is self-locking and lowering needs W r tan(φs − α); if φs < α a holding moment W r tan(α − φs) is needed. Raising efficiency is tan α / tan(α + φs), always below 50% for a self-locking square thread.

Flashcards

Flashcard

Screw thread

An inclined plane wrapped into a helix round a cylinder

Driven by a moment, not a push.

Test your understanding

Question 1 of 5

A single-start square thread has a mean diameter of 40 mm and a pitch of 8 mm. What is its lead angle?

Question 2 of 5

A square-thread screw with a mean radius of 20 mm and lead angle 3.0° raises a 5,000 N load, with μs = 0.12. What moment is needed at impending motion?

Question 3 of 5

A lead screw has a pitch of 2 mm and three starts. How far does it advance in one full turn?

Question 4 of 5

A square-thread screw has a lead angle of 6.5° and μs = 0.10. It carries an axial load and no moment is applied. What happens?

Question 5 of 5

You look at the head of a bolt with an ordinary right-hand thread and turn it clockwise. What does the bolt do?

← Previous topicNext topic →