Statics › Section H · Internal forces › Topic H.1
Internal forces and sign conventions
Every loaded beam is being pulled, sheared and bent inside, at every point along its length. This topic shows how to expose those hidden forces by cutting the body in your imagination, and fixes the sign convention used for them throughout this section.
Forces you cannot see
Every loaded body carries forces inside it that hold its parts together: the material on one side of any imaginary slice pushes and pulls on the material on the other side. These internal forces come in equal and opposite pairs, by Newton's third law, so they cancel when you view the whole body. To find them, cut the body in your imagination. Each piece must still be in equilibrium, so the actions across the cut become external forces on that piece. They are the first thing a designer computes, because they control stresses and deflections.
Cutting a straight two-force member
Recall from Structures and two-force members that a straight member loaded only at its ends carries equal and opposite end forces along its axis. Cut it anywhere: each piece has one end force, balanced by an opposite force at the cut along the same line. So a straight two-force member carries only axial force, tension or compression, the same at every cut. This is the assumption behind truss analysis in How trusses work.
A bent member needs more
Now bend the member into an L, still pinned only at its two ends. The end forces still act along the straight line joining the pins, but that line no longer runs through the material. Cut one leg and balance the end force with a single force at the cut: the two forces are offset, so they form a couple and the piece would rotate. A couple is needed at the cut too. In a plane body the material across a cut acts like a fixed support, resisting sliding in two directions and rotation.
Normal force, shear force and bending moment
The force at a cut is resolved relative to the cut face. The normal force \(N\) acts perpendicular to the face; when the cut is square to the member's axis it is also called the axial force. The shear force \(V\) acts parallel to the face and tends to slide one side past the other, like two sheets of paper pushed in opposite directions. The bending moment \(M\) is the couple at the cut, which tends to bend the material. All three are resultants of forces spread over the whole face, which mechanics of materials later turns into stresses.
Why a new sign convention is needed
In an equilibrium equation a force is positive if it points in the positive x or y direction. That rule fails for internal forces, because at any cut the shear on one face points up and the shear on the other face points down. So the sign of an internal force must describe what it does to the material. The convention on the next card labels every result in this section, but equilibrium equations are written as before: right, up and counterclockwise positive.
The beam sign convention
Draw the beam horizontal with x increasing to the right, cut it, and look at the two cut faces. Positive normal force is tension: \(N\) pulls away from each face. Positive shear acts downward on the face of the left-hand piece and upward on the face of the right-hand piece; equivalently, it tends to turn a short element of the beam clockwise. Positive bending moment is sagging: it bends the beam concave upward, into a smile. It acts counterclockwise on the face of the left-hand piece and clockwise on the face of the right-hand piece. A negative moment is hogging, which bends the beam concave downward. For a member in another orientation, decide which end counts as the left and keep that choice.
Assume positive, then read the signs
On the free-body diagram of a cut piece, draw \(N\), \(V\) and \(M\) in their positive directions, then solve. A negative answer means the force acts the other way: \(M = -900\) N·m is a hogging moment of 900 N·m. Either piece gives the same three values, so choose the one with fewer forces on it. If one piece has no supports, you do not need the reactions at all.
Worked example: a bent bracket
An L-shaped bracket, pinned at A and C with no other load, is a two-force member. Leg AB runs 0.8 m right from A to B; leg BC runs 0.6 m straight down to C. It carries 5 kN tension along line AC. Find the internal forces at D, the midpoint of AB. 1. AC is 1.0 m long, and tension pulls A away from C, so the force at A is 4 kN left and 3 kN up. 2. Take piece AD; at D draw \(N\) right, \(V\) down, \(M\) counterclockwise. 3. x-forces: \(-4 + N = 0\), so \(N = 4\) kN, tension. 4. y-forces: \(3 - V = 0\), so \(V = 3\) kN. 5. Moments about D: the 3 kN force, 0.4 m to the left, gives 1.2 kN·m clockwise, so \(M = 1.2\) kN·m, sagging. 6. Check: D lies 0.24 m from line AC, and \(5 \times 0.24 = 1.2\).
Worked example: a cantilever's sign
A 2.0 m cantilever is fixed to a wall at its left end A and carries 600 N downward at its free end B. Find the internal forces at C, 0.5 m from the wall. 1. Use piece CB: it has no supports, so no reactions are needed. 2. At C draw \(N\) left, \(V\) up and \(M\) clockwise. 3. No horizontal loads, so \(N = 0\). 4. y-forces: \(V - 600 = 0\), so \(V = 600\) N. 5. Moments about C: the load, 1.5 m away, gives 900 N·m clockwise, so \(-900 - M = 0\) and \(M = -900\) N·m. 6. Hogging: the cantilever curves concave downward, like a diving board. 7. Check with piece AC: the wall gives 600 N up and a 1200 N·m counterclockwise couple, and \(-300 + 1200 + M = 0\).
Sagging, hogging and design
The sign of \(M\) tells a designer which face of a beam is stretched. Under a sagging moment the bottom fibres lengthen, in tension, and the top fibres shorten, in compression; hogging reverses this. Concrete cracks under quite modest tension, so reinforced-concrete beams put steel bars near the tension face: near the bottom in the middle of a simply supported span, and near the top along a cantilever.
Common mistakes to avoid
First, using "up is positive" for internal shear: the sign of \(V\) depends on which face it acts on. Second, drawing the internal forces the same way on both faces; they must be opposite. Third, forgetting the bending moment at a cut. Fourth, assuming a bent two-force member carries axial force alone. Fifth, treating a negative answer as a mistake rather than a direction. Sixth, drawing internal forces on the whole, uncut body, where they cancel.
Key takeaways
An imaginary cut exposes internal forces as equal and opposite actions on two faces: in a plane body, a normal force N, a shear force V and a bending moment M. A straight two-force member carries axial force only; a bent one also carries V and M. With x to the right, positive N is tension, positive V acts down on the left piece's face and up on the right piece's face, and positive M is sagging. Draw them positive, solve, and read a negative answer as a reversed direction.
Flashcards
Flashcard
Forces and couples inside a body that hold its parts together
Test your understanding
Question 1 of 5
A horizontal beam is cut, with x increasing to the right. On the cut face of the left-hand piece, which directions are positive for the shear force and the bending moment?
Question 2 of 5
Solving for the internal forces at a cut gives M = −2.5 kN·m. What does this mean?
Question 3 of 5
An L-shaped bracket pinned only at its two ends carries no other load. Which internal forces can act at a cut through one of its legs?
Question 4 of 5
A 3 m cantilever is fixed at its left end and carries 400 N downward at its free end. What are V and M at a cut 1 m from the wall?
Question 5 of 5
A beam carries a sagging bending moment at a section. Which part of the cross-section is in tension there?
