Statics › Section H · Internal forces › Topic H.5
The graphical method
Once you trust the links between load, shear and moment, you can draw both diagrams with nothing more than jumps, slopes and the areas of rectangles and triangles. It is the quickest way to diagram most everyday beams, and it checks itself as you go.
Integration with geometry
Shear and bending moment diagrams set out two facts: the change in shear is minus the area under the load curve, and the change in moment is the area under the shear diagram. The graphical method uses them directly. Instead of writing \(V(x)\) and \(M(x)\) as formulas, as The section cut method does, you walk along the beam from left to right and build each diagram from jumps, slopes and areas. For point forces, couples and uniform loads every area is a rectangle or a triangle, so the method is fast. Load intensity \(w\) is positive downward, positive shear turns an element clockwise, and positive moment is sagging.
Rules for the shear diagram
Start at \(V = 0\) just left of the beam. At a point force, jump by its size in its own direction: up for an upward reaction, down for a downward load. A couple causes no jump in shear. Over a distributed load, the shear changes by minus the load area, and its slope at each point equals \(-w\), so a uniform downward load gives a straight line falling at rate \(w\). Over an unloaded stretch the shear is horizontal. After the last force at the right end, the shear must be back to zero; if it is not, a reaction or load is wrong.
Rules for the moment diagram
Start at \(M = 0\) at the left end. Over each segment, change the moment by the area under the shear diagram, counting area below the axis as negative. At a concentrated couple, jump up by its size if it is clockwise and down if it is counterclockwise. A fixed support's reaction couple counts too, so a cantilever fixed at its left end begins with such a jump. The slope of the moment diagram equals the shear: steep where \(|V|\) is large, flat where \(V = 0\). The moment must return to zero at the right end unless a fixed support or couple acts there.
Shapes and curvature
Where the shear is constant, the moment is a straight line. Where the shear is a sloping straight line, as under a uniform load, the moment is a parabola. Under a downward load the shear is decreasing, so the slope of the moment diagram decreases and the parabola is concave downward, like a hill. Its peak sits where the shear crosses zero. Draw each piece with the right shape: a straight-line moment segment under a uniform load is a clear sign of an error.
The procedure
1. Find the reactions and check them with a second equilibrium equation. 2. Mark the interesting points: supports, point forces, couples, and the ends of distributed loads. 3. Draw the shear diagram left to right using jumps and load areas. 4. Locate each point where the shear crosses zero; under a uniform load \(w\), the crossing lies a distance \(V_0/w\) past the point where the shear was \(V_0\), by similar triangles. 5. Work out the area of each shear segment. 6. Draw the moment diagram left to right using those areas and any couple jumps. 7. Connect the values with correctly shaped curves and label the peaks.
Worked example: an overhang, shear
Beam ABC has a pin at A (\(x = 0\)), a roller at B (\(x = 6\) m) and a free end C (\(x = 8\) m). It carries 5 kN/m from A to B and 6 kN downward at C. 1. Moments about A: \(6B = 30(3) + 6(8) = 138\), so \(B = 23\) kN and \(A = 36 - 23 = 13\) kN. 2. Shear: jump up to +13 kN at A. 3. From A to B, fall by the load area 30 kN, in a straight line, to \(-17\) kN just left of B. 4. Jump up 23 kN to +6 kN at B, stay at 6 kN to C, then drop 6 kN to zero. The check passes. 5. Zero crossing: \(13/5 = 2.6\) m from A.
Worked example: an overhang, moment
Continue with the same beam. 1. Area from 0 to 2.6 m: a triangle, \(\tfrac{1}{2}(2.6)(13) = 16.9\) kN·m, so \(M(2.6) = 16.9\) kN·m. 2. Area from 2.6 m to 6 m: a triangle below the axis, \(\tfrac{1}{2}(3.4)(-17) = -28.9\) kN·m, so \(M(6) = -12\) kN·m. 3. Area from 6 m to 8 m: \(6 \times 2 = 12\) kN·m, so \(M(8) = 0\), as a free end requires. Description: \(M\) is a concave-down parabola from zero up to a sagging peak of 16.9 kN·m at 2.6 m, falling through zero at 5.2 m to a hogging −12 kN·m over B, then a straight line back to zero at C.
Worked example: a concentrated couple
A 6 m beam has a pin at A, its left end, and a roller at B, its right end. Its only load is a 12 kN·m clockwise couple at \(x = 2\) m. 1. Moments about A: \(-12 + 6B = 0\), so \(B = 2\) kN up, and \(A = -2\) kN, pulling down. 2. Shear: drop to −2 kN at A, stay there to B, then rise 2 kN to zero; the couple causes no jump. 3. Moment: the area from 0 to 2 m is −4 kN·m, so \(M = -4\) kN·m just left of the couple. 4. The clockwise couple jumps \(M\) up 12 kN·m, to +8 kN·m. 5. The area from 2 m to 6 m is −8 kN·m, bringing \(M\) to zero at B. Description: two parallel straight lines, falling from 0 to −4, then from +8 to 0.
Strengths and limits
The graphical method is quick, needs only a few calculations, and has built-in checks: the shear must close to zero, and so must the moment at a free or pinned end. It is ideal for point forces, couples and uniform loads. For a triangular or curved load, the shear becomes a parabola or a higher curve, and finding its zero crossings and areas with geometry gets awkward. The integration method, the next topic, handles those loads.
Common mistakes to avoid
First, making the shear jump at a couple; only the moment jumps. Second, jumping the moment the wrong way: clockwise couples move it up. Third, drawing straight lines on the moment diagram under a uniform load, where it must be a parabola. Fourth, placing a moment peak by eye instead of where the shear crosses zero or changes sign; over an interior support that can be a hogging peak. Fifth, counting a shear area below the axis as positive. Sixth, ignoring a diagram that fails to close: it signals an error.
Key takeaways
Walk left to right. Shear: jump by each point force in its direction, no jump at couples, change by minus the load area, slope −w. Moment: change by the area under the shear, jump up for clockwise couples and down for counterclockwise ones, slope V. Constant shear gives straight moment lines; sloping shear gives parabolas, concave down under downward load. Under uniform load the shear crosses zero V₀/w past where it was V₀. Both diagrams must close at the ends.
Flashcards
Flashcard
Building V and M diagrams from jumps, slopes and areas
Test your understanding
Question 1 of 5
At the start of a 4 m stretch carrying a uniform downward load of 3 kN/m, the shear is 9 kN. How far along the stretch does the shear reach zero?
Question 2 of 5
The shear is 13 kN at x = 0 and falls in a straight line to zero at x = 2.6 m. If M = 0 at x = 0, what is M at x = 2.6 m?
Question 3 of 5
Just left of a point the moment is 5 kN·m. A counterclockwise couple of 8 kN·m acts at that point. What is the moment just to its right?
Question 4 of 5
Over a stretch with a uniform downward load, the shear diagram is a sloping straight line. What shape is the moment diagram there?
Question 5 of 5
You finish the shear diagram of a simply supported beam, and after the right-hand reaction it ends at +4 kN rather than zero. What does this tell you?
