Statics › Section H · Internal forces › Topic H.4

The section cut method

Make the cut at a variable position x instead of a fixed point, and equilibrium gives the shear and bending moment as functions along the whole beam. Plot those functions and you have the shear and moment diagrams.

From a point to a function

In Internal forces at a point, a cut at one chosen place gave numbers for \(V\) and \(M\). The section cut method makes the same cut at a general position \(x\) measured from the left end. Equilibrium of the cut piece then gives formulas \(V(x)\) and \(M(x)\). Substituting any \(x\) gives the internal forces there, and plotting the formulas gives the diagrams described in Shear and bending moment diagrams. The sign convention is unchanged: positive shear turns an element clockwise, and positive moment is sagging.

Loading segments

One formula rarely covers a whole beam. Each time the cut passes a support, a point force, a couple, or the start or end of a distributed load, the free-body diagram of the cut piece changes, so the formulas change too. These are the beam's interesting points, and they divide it into loading segments. Each segment gets its own pair of equations, valid only on that range of \(x\). At a point force the shear has one value just to the left and another just to the right, so the equations do not give a single value exactly there.

The procedure

1. Find the support reactions from a free-body diagram of the whole beam. 2. Mark the interesting points and list the segments. 3. For each segment, cut at a general \(x\) inside it and draw the piece to the left of the cut, or the right if that is simpler, with \(V\) and \(M\) positive on its face. 4. Write vertical force and moment equations, taking moments about the cut, and solve for \(V(x)\) and \(M(x)\). 5. State each range. 6. Check the results, then plot.

Loads on a piece of length x

The loads on the cut piece must be written in terms of \(x\). A uniform load \(w\) covering the whole left piece has resultant \(wx\), acting at \(x/2\) from the left end, so its moment arm about the cut is also \(x/2\). If the cut lies beyond the end of a partial uniform load, its resultant is fixed, and its arm about the cut is \(x\) minus the position of its centroid. For a right-hand piece, the length is \(L - x\) for a beam of length \(L\), and each arm is measured from the cut to the right.

Worked example: a cantilever

A 3 m cantilever is fixed at its left end, carries 2 kN/m along its full length and 4 kN downward at its free end. 1. Use the right piece, of length \(3 - x\): no reactions are needed. 2. Its loads are \(2(3 - x)\) kN at \((3 - x)/2\) from the cut, and 4 kN at \(3 - x\). 3. Vertical forces: \(V(x) = 2(3 - x) + 4 = 10 - 2x\) kN. 4. Moments about the cut, with \(M\) clockwise on this face:

M(x) = -(3 - x)^2 - 4(3 - x) = -x^2 + 10x - 21

in kN·m. 5. Check: \(dM/dx = -2x + 10 = V\). Description: \(V\) is a straight line from 10 kN at the wall to 4 kN at the tip. \(M\) is a concave-down parabola, hogging throughout, rising from −21 kN·m at the wall to zero at the tip.

Worked example: three segments

A 10 m beam has a pin at A, its left end, and a roller at B, its right end. It carries 6 kN/m from \(x = 0\) to 4 m and a 20 kN downward load at \(x = 7\) m. 1. Moments about A: \(10B = 24(2) + 20(7) = 188\), so \(B = 18.8\) kN and \(A = 44 - 18.8 = 25.2\) kN. 2. Segment 1, \(0 < x < 4\): the left piece carries \(6x\) at \(x/2\), so \(V = 25.2 - 6x\) and \(M = 25.2x - 3x^2\). 3. Segment 2, \(4 < x < 7\): the full 24 kN acts at 2 m, so \(V = 1.2\) and \(M = 25.2x - 24(x - 2) = 1.2x + 48\). 4. Segment 3, \(7 < x < 10\): \(V = -18.8\) and \(M = 1.2x + 48 - 20(x - 7) = 188 - 18.8x\).

Reading the three-segment results

Key values: \(M(4) = 52.8\) kN·m from both segments 1 and 2, \(M(7) = 56.4\) kN·m, and \(M(10) = 0\), as a roller requires. The shear is positive until \(x = 7\) m, where it drops from 1.2 kN to −18.8 kN, so the largest moment is 56.4 kN·m at the point load. Description: \(V\) falls in a straight line from 25.2 kN to 1.2 kN over the first 4 m, stays at 1.2 kN to 7 m, drops by 20 kN, and stays at −18.8 kN to B. \(M\) is a concave-down parabola up to 52.8 kN·m, then straight lines up to 56.4 kN·m and down to zero.

A trap: roots outside the range

To find a peak moment, solve \(V(x) = 0\) within each segment. In segment 1 above, \(25.2 - 6x = 0\) gives \(x = 4.2\) m, but segment 1 ends at 4 m, so that root is not a real zero of the shear: beyond 4 m a different formula applies. A root counts only if it lies inside its segment's range. When no root does, look for the peak at a segment boundary where the shear changes sign, as it did at 7 m.

Checks before you plot

Run three quick checks. First, \(M\) must agree at each boundary between segments unless a couple acts there. Second, in every segment \(dM/dx\) must equal \(V(x)\), and \(dV/dx\) must equal \(-w\). Third, the end values must fit the supports: \(M = 0\) at a free end, or at a pin or roller on the end of the beam, unless a couple is applied there. The method works for any loading, and its formulas suit spreadsheets and software, but it becomes slow when a beam has many segments. The next two topics offer faster routes.

Common mistakes to avoid

First, using one pair of equations across a point load or the end of a distributed load. Second, putting a distributed load's resultant at the wrong place: once the cut is past the load, the arm is \(x\) minus the centroid position. Third, forgetting to state each segment's range. Fourth, accepting a zero of \(V\) that lies outside its segment. Fifth, drawing \(M\) counterclockwise on a right-hand piece, where positive \(M\) is clockwise.

Key takeaways

The section cut method cuts at a general x in each loading segment, draws V and M positive, and uses equilibrium to find V(x) and M(x). Segments are separated by supports, point forces, couples and the ends of distributed loads. Each formula holds only on its own range. Check that M is continuous at boundaries without couples, that dM/dx = V, and that end values suit the supports. The peak moment occurs where V is zero inside a segment or changes sign at a boundary.

Flashcards

Flashcard

Section cut method

Cut at a general x and use equilibrium to find V(x) and M(x)

Plot them to get the diagrams.

Test your understanding

Question 1 of 5

A 12 m beam has a pin at x = 0, a roller at x = 12 m, a point load at x = 3 m and a uniform load from x = 6 m to x = 12 m. How many loading segments does it have?

Question 2 of 5

A 4 m cantilever is fixed at its left end and carries 3 kN/m along its full length. Using the right-hand piece, what are V(x) and M(x)?

Question 3 of 5

In a segment valid for 0 < x < 4 m, V(x) = 25.2 − 6x, and solving V = 0 gives x = 4.2 m. What should you conclude?

Question 4 of 5

A 6 m simply supported beam has reactions of 8 kN at the left end and 4 kN at the right end, and a 12 kN load at x = 2 m. Using the left piece, what is M(x) for 2 < x < 6 m?

Question 5 of 5

Why do the section cut equations not give a single value of the shear exactly at a point where a concentrated force acts?

← Previous topicNext topic →