Statics › Section H · Internal forces › Topic H.2

Internal forces at a point

Weak spots such as bolt holes, welds and changes of section make engineers ask what is happening inside a beam at one particular place. This topic gives a reliable procedure for finding the normal force, shear force and bending moment at any one chosen point of a beam or frame member.

Why one point matters

Designers often need the internal forces at one particular place: where a hole is drilled for a bolt, where two beam sections are welded together, or where a pipe is clamped to a bracket. The previous topic, Internal forces and sign conventions, showed that a cut exposes a normal force \(N\), a shear force \(V\) and a bending moment \(M\). Here that idea becomes a step-by-step method that works for any multi-force body. Straight two-force members are the easy exception: they carry axial force only, so their internal force follows straight from the member force.

The procedure

1. Draw a free-body diagram of the whole body and find the support reactions, as in Supports, reactions, and free-body diagrams. 2. Cut the body at the point of interest and separate the two pieces. 3. Choose one piece and draw \(N\), \(V\) and \(M\) on its cut face in their positive directions: tension, shear turning the element clockwise, and sagging moment. 4. Apply the three equilibrium equations to that piece. 5. Read the signs: a negative result acts opposite to the way it was drawn. The internal forces appear only on the cut piece, never on the diagram of the whole body.

Cut the distributed load too

To find reactions you may replace a distributed load by its resultant, as in Distributed loads. Once the beam is cut, though, each piece carries only its own share of the load. If 4 kN/m acts along a whole beam and you cut 2 m from the left end, the left piece carries \(4 \times 2 = 8\) kN acting at its own centroid, 1 m from the left end. Using the resultant of the whole load on one piece gives a wrong shear and a wrong moment. Always redraw the distributed load on the piece, then find its resultant.

Sum moments about the cut

For the moment equation, take moments about the point where the cut is made. The normal force and the shear force both act through that point, so they drop out, and \(M\) is the only unknown left. The force equations give \(N\) and \(V\) directly as well. In the sums, use the usual equilibrium signs: forces right and up positive, moments counterclockwise positive. Then remember that positive \(M\) is counterclockwise on the left piece's face but clockwise on the right piece's face.

Worked example: a loaded floor beam

A 6 m beam has a pin at A, its left end, and a roller at B, its right end. It carries 4 kN/m along its full length and a 9 kN downward load 4 m from A. Find the internal forces at C, 2 m from A. 1. Moments about A: \(6B = 24(3) + 9(4) = 108\), so \(B = 18\) kN. Vertical forces: \(A_y = 33 - 18 = 15\) kN. No horizontal loads, so \(A_x = 0\). 2. Take the left piece AC: it carries 8 kN of distributed load at 1 m from A. 3. Horizontal forces give \(N = 0\). 4. Vertical forces: \(15 - 8 - V = 0\), so \(V = 7\) kN. 5. Moments about C: \(-15(2) + 8(1) + M = 0\), so \(M = 22\) kN·m, sagging. 6. Check with piece CB: \(V = 16 + 9 - 18 = 7\) kN and \(M = 18(4) - 16(2) - 9(2) = 22\) kN·m.

Choosing the easier piece

Both pieces give the same answers, so pick the one with fewer forces and known values. On a cantilever, or on the overhang of an overhanging beam, the piece between the cut and the free end has no supports on it. Analysing that piece means you can skip the reactions altogether, which saves time and removes a source of error. When the point lies between the supports, you usually need at least one reaction; choose the side with fewer loads to sum.

Worked example: a point on an overhang

Beam AC has a pin at A, a roller at B 4 m to the right, and a free end C 5.5 m from A. At C a 10 kN force acts down and to the right through the beam's axis, with components 8 kN right and 6 kN down. Find the internal forces at D, 5.0 m from A. 1. Use piece DC, 0.5 m long: it has no supports. 2. On its face at D draw \(N\) to the left, \(V\) upward and \(M\) clockwise. 3. Horizontal: \(8 - N = 0\), so \(N = 8\) kN, tension. 4. Vertical: \(V - 6 = 0\), so \(V = 6\) kN. 5. Moments about D: the 6 kN force, 0.5 m away, gives 3 kN·m clockwise, so \(-3 - M = 0\) and \(M = -3\) kN·m. The overhang hogs, as you would expect for a load hanging off the end.

Worked example: a negative reaction

For the same beam, find the internal forces at E, 2 m from A. 1. Moments about A: \(4B - 6(5.5) = 0\), so \(B = 8.25\) kN up. 2. Vertical forces: \(A_y + 8.25 - 6 = 0\), so \(A_y = -2.25\) kN: the pin pulls down 2.25 kN. Horizontal: \(A_x = -8\) kN, 8 kN to the left. 3. Take piece AE with \(N\) right, \(V\) down and \(M\) counterclockwise at E. 4. Horizontal: \(-8 + N = 0\), so \(N = 8\) kN. 5. Vertical: \(-2.25 - V = 0\), so \(V = -2.25\) kN. 6. Moments about E: the downward 2.25 kN, 2 m to the left, gives 4.5 kN·m counterclockwise, so \(M = -4.5\) kN·m. 7. Check with piece EC: \(V = 6 - 8.25 = -2.25\) kN, and \(8.25(2) - 6(3.5) - M = 0\) gives \(M = -4.5\) kN·m.

Members of frames

The same method works inside a frame. A multi-force member, such as a lever arm pinned at three points, carries normal force, shear and moment, while its straight two-force links carry axial force only. First find the pin forces on the member, as in Analyzing frames. Then draw the member alone, cut it at the point of interest, and treat it exactly like a beam. If the member is inclined, resolve the forces along and across it, because \(N\) acts along the member's axis and \(V\) acts perpendicular to it.

Common mistakes to avoid

First, using the resultant of the whole distributed load on one piece instead of only its share. Second, drawing internal forces on the uncut body. Third, drawing \(M\) the same way on either piece: it is counterclockwise on the left piece and clockwise on the right one. Fourth, dropping the sign of a negative reaction when substituting it. Fifth, taking moments about a support instead of the cut, which leaves \(V\) in the moment equation. Sixth, resolving forces along x and y on an inclined member instead of along and across its axis.

Key takeaways

To find internal forces at a point: find the reactions if needed, cut at the point, draw N, V and M positive on one piece, and apply the three equilibrium equations. Each piece carries only its own share of any distributed load. Summing moments about the cut gives M directly. Choose the easier piece; a piece with no supports needs no reactions. Negative results mean reversed directions, and both pieces must agree.

Flashcards

Flashcard

Internal forces at a point

N, V and M found by cutting at that one point

Used at holes, welds and section changes.

Test your understanding

Question 1 of 5

An 8 m simply supported beam carries 4 kN/m along its full length, so each support provides 16 kN. What are V and M at a point 2 m from the left support?

Question 2 of 5

When finding the internal forces at a cut, why is it best to sum moments about the cut point itself?

Question 3 of 5

A beam overhangs its right-hand roller. You need the internal forces at a point on the overhang. Which approach avoids finding any support reactions?

Question 4 of 5

Using the left piece of a cut beam, with V drawn positive, you find V = −2.25 kN. Which way does the shear actually act on the left piece's face?

Question 5 of 5

A beam overhangs its right-hand support. Its free right-hand end carries a force through the beam's axis, with components 3 kN to the right and 4 kN down. What are N, V and M at a cut 1 m from the free end?

← Previous topicNext topic →