Statics › Section H · Internal forces › Topic H.3

Shear and bending moment diagrams

One cut gives the internal forces at one point, but a designer needs them everywhere. Shear and bending moment diagrams show them along the whole beam, and two short equations link them to the load.

Seeing the whole beam at once

A shear diagram plots the internal shear \(V(x)\) against position \(x\) along a beam, and a bending moment diagram plots \(M(x)\). Drawn under a sketch of the loaded beam, they show where the largest shear and moment occur, which is where the beam must be strongest. Here the diagrams are described in words: \(x\) runs from the left end, positive values lie above the axis, and each piece is named by its shape (constant, sloping line, parabola) with its key values and jumps. Signs follow Internal forces and sign conventions: positive shear turns an element clockwise and positive moment is sagging.

Three standard beams

A simply supported beam has a pin at one end and a roller at the other. A cantilever is fixed at one end and free at the other. An overhanging beam rests on a pin and a roller, with one or both ends extending past the supports. All three are statically determinate, so the reactions follow from equilibrium alone. Beams mainly carry loads across their length, so the diagrams here show only \(V\) and \(M\) and ignore axial force. Throughout this section, a distributed load intensity \(w(x)\), in N/m or kN/m, is counted positive when it acts downward.

A thin slice of beam

To link load, shear and moment, take a short slice between \(x\) and \(x + \Delta x\) on a stretch with no point forces or couples. Over so short a length the load is nearly uniform, so it adds a downward force \(w\,\Delta x\) at the slice's centre. The slice's left face is the face of a right-hand piece, so positive \(V\) acts up there and positive \(M\) acts clockwise. Its right face is the face of a left-hand piece, carrying \(V + \Delta V\) downward and \(M + \Delta M\) counterclockwise. Vertical equilibrium gives \(V - w\,\Delta x - (V + \Delta V) = 0\), so \(\Delta V = -w\,\Delta x\).

The two differential relations

Taking moments about the slice's right face gives \(\Delta M = V\,\Delta x - \tfrac{1}{2}w\,\Delta x^2\). Divide both results by \(\Delta x\) and let it shrink to zero:

\frac{dV}{dx} = -w(x), \qquad \frac{dM}{dx} = V(x)

In words, the slope of the shear diagram equals minus the load intensity, and the slope of the moment diagram equals the shear. Some books, including the course's reference text, count upward loads as positive; with that choice the first relation reads \(dV/dx = w\). The physics is the same: a downward load always makes the shear fall.

Areas give changes

Integrating each relation between two points \(a\) and \(b\) gives

V_b - V_a = -\int_a^b w\,dx, \qquad M_b - M_a = \int_a^b V\,dx

The change in shear equals minus the area under the load curve, which is the total downward load between the points. The change in moment equals the area under the shear diagram, counting area below the axis as negative. These hold only on stretches without point forces or couples; at those points the diagrams jump, as the next card explains.

Jumps at point loads and couples

Shrink a slice around a concentrated force and its equilibrium shows that \(V\) changes suddenly by the size of the force. Moving left to right, a downward force \(P\) makes the shear drop by \(P\), and an upward reaction makes it rise. The moment does not jump there, but its slope changes, so the moment diagram has a corner. A concentrated couple leaves the shear unchanged and makes \(M\) jump: up by its size if it is clockwise, down if it is counterclockwise. At a free end, or at a pin or roller on the end of a beam, the moment is zero unless a couple is applied there.

What the relations predict

Where there is no load, \(V\) is constant and \(M\) is a straight line. Under a uniform load, \(V\) is a straight sloping line and \(M\) is a parabola. Because \(dM/dx = V\), the moment rises wherever the shear is positive and falls wherever it is negative. So, unless a concentrated couple acts, the largest moment between the supports occurs where \(V\) passes through zero or changes sign, which may happen at a point load. Under a downward load the shear is falling, so the moment's slope decreases and the diagram curves like a hill, concave downward.

Worked example: a uniformly loaded span

An 8 m simply supported beam carries 3 kN/m along its full length. 1. By symmetry each support provides half of 24 kN, so 12 kN. 2. Cutting at \(x\) and using the left piece gives \(V(x) = 12 - 3x\) kN and \(M(x) = 12x - 1.5x^2\) kN·m. 3. Check the relations: \(dV/dx = -3 = -w\), and \(dM/dx = 12 - 3x = V\). 4. \(V = 0\) at \(x = 4\) m, so the largest moment is \(M(4) = 48 - 24 = 24\) kN·m, which matches \(wL^2/8 = 3(64)/8\). 5. Area check: the shear triangle from 0 to 4 m has area \(\tfrac{1}{2}(4)(12) = 24\) kN·m. Description: \(V\) is a straight line from +12 kN down to −12 kN, crossing zero at mid-span; \(M\) is a parabola, zero at both ends, peaking at 24 kN·m in the middle.

Worked example: a single point load

A 6 m simply supported beam, pin at A and roller at B, carries a 12 kN downward load 2 m from A. 1. Moments about A: \(6B = 12(2)\), so \(B = 4\) kN and \(A = 8\) kN. 2. Shear: rise to +8 kN at A, stay constant to \(x = 2\) m, drop by 12 to −4 kN, stay constant to B, then rise by 4 to zero. 3. Moment at the load: the shear area from 0 to 2 m is \(8 \times 2 = 16\), so \(M(2) = 16\) kN·m. 4. From 2 m to 6 m the area is \(-4 \times 4 = -16\), bringing \(M\) back to zero at B. Description: \(M\) rises in a straight line to 16 kN·m at the load, where the shear changes sign, then falls in a straight line to zero.

Beyond statics

The chain does not stop at the moment. In mechanics of materials you will divide \(M(x)\) by the beam's bending stiffness \(EI\) and integrate twice more to find the slope and the deflection of the bent beam. So load, shear, moment, slope and deflection form one sequence, each found from the one before by integration, and every later check of bending stress or sag starts from the moment diagram.

Common mistakes to avoid

First, mixing load sign conventions: with downward \(w\) positive, \(dV/dx = -w\), not \(+w\). Second, applying the area rules across a point force or couple without adding the jump. Third, making the shear jump at a concentrated couple; only the moment jumps. Fourth, looking for the largest moment where the shear is largest, rather than where it crosses zero. Fifth, forgetting that areas below the shear axis reduce the moment.

Key takeaways

Shear and moment diagrams plot V(x) and M(x) along a beam, with positive values above the axis. With downward load intensity w positive, dV/dx = −w and dM/dx = V. The change in shear is minus the load area, and the change in moment is the area under the shear diagram. Downward point forces make V drop; clockwise couples make M jump up. No load gives constant V and straight-line M; uniform load gives straight-line V and parabolic M. Unless a couple acts, the largest moment occurs where V is zero or changes sign.

Flashcards

Flashcard

Shear diagram

A plot of internal shear V(x) along the beam

Positive values above the axis.

Test your understanding

Question 1 of 5

Along a stretch of a beam that carries no load at all, what shapes do the shear and moment diagrams have?

Question 2 of 5

On a beam segment from x = 3 m to x = 7 m the shear is constant at −5 kN, and M = 12 kN·m at x = 3 m. What is M at x = 7 m?

Question 3 of 5

A uniform downward load of 6 kN/m acts from x = 1 m to x = 4 m, with no point loads there. If V = 10 kN at x = 1 m, what is V at x = 4 m?

Question 4 of 5

A simply supported beam carries only downward loads. Where between the supports is the bending moment largest?

Question 5 of 5

A clockwise concentrated couple of 10 kN·m acts on a beam at x = 3 m. Moving from left to right past that point, what happens to the diagrams?

← Previous topicNext topic →