Statics › Section I · Friction › Topic I.7
Rotating discs
When a flat face spins against another, friction acts over the whole contact area and resists the rotation with a moment. Adding up that moment is a short integral, and its result sizes thrust bearings, clutches and the disc brakes on a car.
Friction on a turning face
Disc friction is the friction between a flat face that rotates about an axis perpendicular to it and a surface it presses against. It produces a moment opposing the relative rotation. A collar bearing is a ring-shaped shoulder on a shaft that presses on a fixed surface and carries the shaft's axial load. An end bearing supports the flat end of a shaft. A disc brake squeezes pads against a spinning disc, a clutch presses two discs together, and a sanding disc rubs on a workpiece. In every case we want the moment \(M\) that friction exerts for a given axial force \(P\).
Why the outer rim matters more
Assume, as this course does, that the pressure \(p\) between the faces is the same everywhere and that one coefficient applies everywhere. Then every small patch of contact carries the same friction force per unit area, \(\mu p\), acting along the direction of sliding, which is tangential, perpendicular to the radius. But a patch near the outer edge has a long moment arm about the axis, and a patch near the centre a short one, so the outer part of the face does most of the work of resisting rotation.
Setting up the integral
Split the contact area into thin rings of radius \(r\) and width \(dr\), each with area \(dA = 2\pi r\,dr\). The friction on a ring is \(\mu p\,dA\), all at moment arm \(r\), so
For a ring-shaped contact with inner radius \(r_i\) and outer radius \(r_o\), uniform pressure means
The constants come outside the integral, which leaves only \(\int r^2\,dr\) from \(r_i\) to \(r_o\), equal to \((r_o^3 - r_i^3)/3\). This is the same strategy of slicing and summing used in the topic "Centroids by integration".
The collar bearing formula
Putting the pieces together gives the friction moment for a ring-shaped contact under uniform pressure:
It is worth reading it as \(M = \mu P r_{eff}\): the whole friction force \(\mu P\) acting at an effective radius \(r_{eff}\), which is the fraction multiplied by \(\frac{2}{3}\). The effective radius always lies between \(r_i\) and \(r_o\), beyond the mean radius, because the outer part of the ring has more area. For a thin ring it approaches the mean radius. A rotating face rubs continuously, so use \(\mu_k\); use \(\mu_s\) to find when a clutch that is not yet slipping will start to slip.
Solid faces: end bearings
When the contact is a full circle of radius \(R\), as at the flat end of a shaft or under a sanding disc, set \(r_i = 0\). The fraction becomes \(R^3/R^2 = R\), so
The friction acts, in effect, at two thirds of the radius. For example, a vertical shaft of diameter 40 mm whose flat end presses on a fixed plate with an axial load of 2.0 kN, with \(\mu_k = 0.20\), needs \(M = \frac{2}{3} \times 0.20 \times 2000 \times 0.020 = 5.33\) N·m to keep turning. Using the full radius as the moment arm would overestimate it by half, at 8.0 N·m.
Worked example: a collar bearing
A vertical shaft carries an axial load of 6.0 kN on a collar whose contact ring has inner radius 25 mm and outer radius 50 mm. The collar turns on a fixed plate with \(\mu_k = 0.12\) and uniform pressure. Find the friction moment and the power lost at 300 rev/min. 1. Fraction:
2. Effective radius: \(\frac{2}{3} \times 0.0583 = 0.0389\) m, just beyond the mean radius of 0.0375 m. 3. Moment: \(M = 0.12 \times 6000 \times 0.0389 = 28.0\) N·m. 4. Angular speed: \(\omega = 300 \times 2\pi/60 = 31.4\) rad/s. 5. Power lost to friction: \(M\omega = 28.0 \times 31.4 = 880\) W, all of it turned into heat at the collar.
Disc brakes
A disc brake pad does not cover a full ring. It covers a sector of it: the part of the ring between \(r_i\) and \(r_o\) that lies within some angle \(\theta\). With the same clamping force on a smaller area, the pressure is higher, but there is less area for it to act on. For uniform pressure the two effects cancel exactly, and the moment from one pad is given by the collar bearing formula, whatever the angle \(\theta\). Most brakes clamp the disc between two pads, one on each face, each pressed with force \(P\), so the total braking moment is
Worked example: a car's disc brake
A caliper presses two pads, one on each face of a spinning brake disc, each with a force of 4.0 kN. The pads cover the region between radii 90 mm and 140 mm, and \(\mu_k = 0.40\). Find the braking moment. 1. Fraction:
2. One pad: \(\frac{2}{3} \times 0.40 \times 4000 \times 0.1752 = 186.9\) N·m. 3. Two pads: \(M = 2 \times 186.9 = 373.8\) N·m. 4. Check: the effective radius is \(\frac{2}{3} \times 0.1752 = 0.117\) m, between 90 mm and 140 mm and just beyond the mean of 115 mm. Two pads give a friction force of \(2 \times 0.40 \times 4000 = 3200\) N, and \(3200 \times 0.117 = 374\) N·m agrees.
Beyond basic statics: uniform wear
Every formula above assumes uniform pressure, which is reasonable for new, accurately flat faces. After running in, the outer part of a face, which slides faster, wears more, until the faces settle into a pattern where the pressure is higher near the centre. Machine designers model that state as uniform wear, in which pressure is inversely proportional to radius. It gives a slightly smaller moment, \(M = \frac{1}{2}\mu P(r_o + r_i)\): 27.0 N·m for the collar in the worked example instead of 28.0 N·m. This model goes beyond basic statics, so every example and question in this topic uses uniform pressure.
Common mistakes to avoid
First, writing the moment as \(\mu P r_o\), with all the friction at the outer edge. Second, using the area of a full circle, \(\pi r_o^2\), for a ring-shaped contact when finding the pressure. Third, forgetting to double the moment for a brake with a pad on each face. Fourth, thinking the pad's arc angle changes the moment under uniform pressure; it does not. Fifth, mixing millimetres and metres inside the cubic fraction, which shifts the answer by powers of ten. Sixth, using revolutions per minute directly in the power \(M\omega\); convert to radians per second.
Key takeaways
Disc friction resists relative rotation of flat faces with a moment. With uniform pressure and coefficient, each ring of radius r contributes dM = μ p r dA, so outer rings matter most. A ring contact gives M = (2/3) μ P (ro³ − ri³)/(ro² − ri²), the friction force μP acting at an effective radius beyond the mean radius. A solid face gives M = (2/3) μ P R. A brake pad sector gives the ring result whatever its angle, doubled for two pads. Use μk for continuous rubbing and convert to rad/s for power. Beyond basic statics, worn faces are modelled by uniform wear, which gives a slightly smaller moment.
Flashcards
Flashcard
Friction between flat faces in relative rotation, giving a moment
Test your understanding
Question 1 of 5
The flat end of a shaft of radius 30 mm presses on a fixed plate with an axial force of 1,500 N. Assuming uniform pressure and μk = 0.15, what moment keeps the shaft turning?
Question 2 of 5
A new collar bearing has a contact ring from 30 mm to 60 mm radius, carries 5,000 N of axial load and has μk = 0.10. Assuming uniform pressure, what is the friction moment?
Question 3 of 5
A brake caliper presses two pads, one on each face of a disc, each with 3,000 N. The pads cover radii 80 mm to 120 mm and μk = 0.35. Assuming uniform pressure, what is the braking moment?
Question 4 of 5
Under uniform pressure, why does a ring of contact near the outer edge of a collar contribute more friction moment than an equal-width ring near the inner edge?
Question 5 of 5
A thrust collar's friction moment is 20 N·m while the shaft turns at 600 rev/min. How much power does the friction dissipate?
