Statics › Section C · Equilibrium of particles › Topic C.2
1D equilibrium: cables, springs, and pulleys
When every force on a body lies along one line, equilibrium is a single equation. That makes one-dimensional problems the ideal place to master the models engineers use everywhere: ideal cables, linear springs, and pulleys that redirect a pull or multiply it.
Forces along one line
The simplest equilibrium problems have every force on one line: a load hanging from a rope, a spring holding a weight, a rope running over a pulley to a hanging bucket. With one direction there is one equation, such as \(\sum F_y = 0\), and at most one unknown. The physics is easy, so these problems are the place to build the habits that the harder ones need: a free-body diagram, a stated positive direction, signed components, units, and a check at the end.
Scalar components and signs
Along one axis, each force can be written as a scalar component times a unit vector, such as \(\mathbf{W} = -W\,\mathbf{j}\) for a weight. The scalar component, here \(-W\), is a signed number: its size is the magnitude and its sign gives the sense, positive towards the positive end of the axis. A magnitude is never negative; a component may be. Components along the same axis add as ordinary numbers. Forces of +250 N, −400 N and +90 N along x have a resultant component of −60 N, which is a 60 N force in the negative x direction.
Two-force bodies
A body acted on by exactly two forces is in equilibrium only if the forces are equal in magnitude, opposite in direction and share one line of action, or are both zero. If the two forces point away from each other the body is in tension; if they point towards each other it is in compression. A rope, a cable, a spring and a light strut pinned at both ends are all two-force bodies when their own weight is small next to the forces they carry. That is why the force in a light strut, pinned at both ends and loaded only at its pins, lies along the line joining them.
Ideal cables
An ideal cable is weightless and inextensible, and it carries only tension, directed along its length. Cut a straight segment anywhere and an FBD of either piece shows the same tension, so one symbol covers the whole segment. A rope pulled with 600 N at each end carries 600 N, not 1,200 N: cut it in the middle, and each half has 600 N at its end balanced by the tension at the cut. Real cables have weight and sag into a curve called a catenary, which matters for long spans such as power lines.
Linear springs
A linear spring exerts a force proportional to its change in length:
Here \(k\) is the stiffness in N/m, \(L_0\) the unstretched length and \(L\) the current length. A positive \(s\) is a stretch and the spring pulls on whatever holds its ends; a negative \(s\) is a compression and it pushes. Always measure \(s\) from the unstretched length, never from an earlier loaded position. Springs model real coil springs, and also flexible supports such as rubber engine mounts.
Worked example: springs holding a parcel
A 3.0 kg parcel hangs from a spring with \(k = 600\) N/m and an unstretched length of 0.25 m. 1. FBD of the parcel: its weight, \(3.0(9.81) = 29.43\) N, acts down and the spring pulls up. 2. \(\sum F_y = 0\) gives a spring force of 29.43 N. 3. Stretch: \(s = 29.43/600 = 0.0491\) m, so the spring is \(0.25 + 0.049 = 0.299\) m long. 4. Two such springs end to end: an FBD of each spring shows that each carries the full 29.43 N, so each stretches 49.1 mm and the pair 98.1 mm. 5. Two side by side, sharing the parcel equally: each carries 14.7 N and stretches 24.5 mm.
Ideal pulleys
An ideal pulley is weightless and turns on a frictionless bearing. A rope passing over it has the same tension on both sides, so the pulley changes the direction of the pull but not its size. To hold a 200 N bucket with a rope over a single fixed pulley, you still pull with 200 N, only now downwards, which suits your body better. The pulley's axle carries both rope forces: when the rope leaves vertically on both sides, the axle must support \(2T\), here 400 N.
The block and tackle
In a block and tackle one rope winds around pulleys in a fixed upper block and a moving lower block. If n rope segments support the moving block, each carries the same tension T, so an FBD of the moving block and its load gives
The ratio \(W/T = n\) is the ideal mechanical advantage. It is paid for in distance: to raise the load by h, each of the n segments must shorten by h, so you pull \(nh\) of rope. Real pulleys lose some force to bearing friction at every pulley, so the real pull is more than W/n, and the gap grows as pulleys are added.
Worked example: an engine hoist
A 120 kg engine hangs from the moving block of a tackle with 4 supporting segments, all vertical. Treat the rope and pulleys as ideal and the moving block as light. 1. FBD of the moving block and engine: four tensions T up, and the weight \(120(9.81) = 1177.2\) N down. 2. \(\sum F_y = 0\) gives \(4T = 1177.2\), so \(T = 294\) N, the pull on the free end. 3. To lift the engine 0.75 m, each segment shortens by 0.75 m, so the mechanic pulls \(4(0.75) = 3.0\) m of rope. 4. Check: the work put in, \(294.3 \times 3.0 = 883\) J, equals the work done lifting, \(1177.2 \times 0.75 = 883\) J.
Common mistakes to avoid
First, doubling the tension in a rope pulled from both ends: equal pulls of P give a tension of P. Second, measuring a spring's stretch from a loaded length instead of its unstretched length. Third, assuming a single fixed pulley reduces the force; it only redirects it. Fourth, counting rope segments that do not hold up the moving block. Fifth, confusing a negative scalar component with a negative magnitude. Sixth, forgetting that a pulley's axle or anchor carries the rope tension on both sides.
Key takeaways
Along one line, forces are signed scalar components that add as numbers, giving one equation and at most one unknown. A two-force body in equilibrium carries equal, opposite, collinear forces and is in tension or compression. An ideal cable has one tension along each straight segment. A linear spring obeys F = ks, with s measured from the unstretched length. An ideal pulley redirects a tension without changing it. A block and tackle with n supporting segments needs a pull of W/n, but n times the rope travel.
Flashcards
Flashcard
A signed number giving a force's size and sense along an axis
Test your understanding
Question 1 of 5
A 5.0 kg mass hangs at rest from a spring with k = 1,000 N/m. How far is the spring stretched? Use g = 9.81 m/s².
Question 2 of 5
An ideal block and tackle has 3 rope segments supporting the moving block, which carries a 900 N load. What pull is needed on the free end?
Question 3 of 5
Two people pull on opposite ends of a light rope with 600 N each, and nothing moves. What is the tension in the rope?
Question 4 of 5
Two identical springs, each with k = 500 N/m, hang end to end and carry a 40 N load. By how much does the pair stretch in total?
Question 5 of 5
A mechanic raises a load by 0.5 m with an ideal tackle that has 4 segments supporting the moving block. How much rope must she pull?
