Statics › Section J · Moments of inertia › Topic J.5
Polar moment of inertia
Bending depends on how area is spread about an axis in the plane; twisting depends on how it is spread about a point. The polar moment of inertia measures that, and it is the number that sizes every drive shaft.
Spread about a point
A car's drive shaft, a drill bit and a wrench extension all carry torque by twisting. When a round shaft twists, each small piece of its cross-section slides sideways around the centre, and the pieces far from the centre resist most. The property that captures this is the polar moment of inertia, introduced in the topic Integral properties of shapes. Instead of measuring distance from an axis lying in the plane, it measures distance \(r\) from a point \(O\):
You can also picture \(O\) as the place where an axis perpendicular to the plane pierces it, such as the centre line of a shaft. The units are again length to the fourth power.
The link to Ix and Iy
Put the origin at \(O\). By Pythagoras every piece of area has \(r^2 = x^2 + y^2\), so the integral splits in two:
This holds for any shape and for any pair of perpendicular axes crossing at \(O\), so turning the axes about \(O\) changes \(I_x\) and \(I_y\) but never their sum. It means you rarely integrate for \(J\) directly: find the two rectangular moments and add. For the T-section of the previous topic, about its centroid,
Circles and tubes
The topic Moments of inertia of common shapes integrated thin rings to get the polar moment of a solid circle about its centre:
It is exactly twice the value about a diameter, \(\pi r^4/4\), as \(J = I_x + I_y\) requires. For a hollow circular shaft of outer radius \(r_o\) and inner radius \(r_i\), subtract the missing core:
Because the fourth power heavily rewards the outermost material, a tube can be much stiffer in twisting than a solid shaft that uses the same amount of metal, as a worked example below shows.
Rectangles and moving the point
For a rectangle \(b\) wide and \(h\) tall, adding \(bh^3/12\) and \(hb^3/12\) gives the polar moment about its centroid:
To move to another point \(P\), apply the parallel axis theorem to \(I_x\) and \(I_y\) separately and add the results. The two shifts, \(Ad_x^2\) and \(Ad_y^2\), combine by Pythagoras into one:
where \(d\) is the straight-line distance from the centroid \(C\) to \(P\). As before, the centroid gives the smallest polar moment, and the theorem must start from it.
Worked example: a rectangle about two points
A plate is 60 mm wide and 20 mm tall. Find its polar moment about its centroid and about one corner. 1. About the centroid: \(I_x = 60(20)^3/12 = 40{,}000\ \mathrm{mm^4}\) and \(I_y = 20(60)^3/12 = 360{,}000\ \mathrm{mm^4}\), so \(J_C = 400{,}000\ \mathrm{mm^4}\). 2. The corner is 30 mm across and 10 mm up from the centroid, so \(d^2 = 30^2 + 10^2 = 1000\ \mathrm{mm^2}\). 3. With \(A = 1200\ \mathrm{mm^2}\),
4. Check another way, about the corner's own axes:
Notice that the long side dominates both answers.
Shafts in torsion
In the course Mechanics of Materials you will show that when an elastic circular shaft carries a torque \(T\), the shear stress grows in proportion to the distance \(\rho\) from the centre. Adding up the moments of those stresses over the section brings in exactly \(\int \rho^2\,dA = J\), and the result is
where \(c\) is the outer radius. A larger \(J\) means a lower stress for the same torque, and a shaft that twists through a smaller angle. With \(T\) in N·mm, lengths in mm and \(J\) in \(\mathrm{mm^4}\), the stress comes out in \(\mathrm{N/mm^2}\), which is the same as megapascals.
Worked example: solid or hollow shaft
A shaft must carry 500 N·m. Compare a solid shaft of diameter 40 mm with a tube of outer diameter 50 mm and inner diameter 30 mm. 1. Areas: both are \(1257\ \mathrm{mm^2}\), so they use the same amount of steel. 2. Solid: \(J = \pi(40)^4/32 = 251{,}300\ \mathrm{mm^4}\), and with \(T = 500{,}000\) N·mm and \(c = 20\) mm,
3. Tube: \(J = \frac{\pi}{2}(25^4 - 15^4) = 534{,}100\ \mathrm{mm^4}\), and with \(c = 25\) mm, \(\tau_{\max} = 23.4\) MPa. 4. Check: the tube's \(J\) is 2.125 times larger, and its peak stress is about 41% lower, using no extra material.
A caution about other shapes
The sum \(J = I_x + I_y\) is a geometric fact for every area, but the stress formula \(\tau = T\rho/J\) is only valid for solid or hollow circular shafts. When a square or rectangular bar twists, its cross-sections do not stay flat; they warp out of their plane, and the real stiffness in twisting is noticeably lower than \(J\) predicts. Engineers handle those shapes with a separate torsion constant from published tables. In statics, treat \(J\) as a property of area that you can calculate for any shape, and keep in mind that its use in torsion design is reliable only for round sections.
Common mistakes to avoid
First, using \(\pi d^4/64\), the value about a diameter, where a shaft needs \(J = \pi d^4/32\). Second, putting the diameter into \(\pi r^4/2\), which makes \(J\) 16 times too large. Third, mixing units in \(\tau = Tc/J\): with \(J\) in \(\mathrm{mm^4}\) the torque must be in N·mm, so 500 N·m becomes 500,000 N·mm. Fourth, adding the horizontal and vertical offsets as \(d = d_x + d_y\) instead of using \(d^2 = d_x^2 + d_y^2\). Fifth, applying \(\tau = Tc/J\) to a rectangular bar.
Key takeaways
The polar moment of inertia J_O = ∫r² dA measures how area is spread about a point, in length to the fourth power. For any shape, J_O = Ix + Iy for perpendicular axes crossing at O. A solid circle has J = πr⁴/2 = πd⁴/32, a tube J = π(ro⁴ − ri⁴)/2, and a rectangle J_C = bh(b² + h²)/12 about its centroid. Moving to another point gives J_P = J_C + Ad², with d the straight-line distance from the centroid. For circular shafts, τmax = Tc/J, so a larger J means lower stress. A tube can carry the same torque at far lower stress than a solid shaft of equal area.
Flashcards
Flashcard
Polar moment of inertia about the point O
Test your understanding
Question 1 of 5
A solid circular shaft has a diameter of 60 mm. Find J about its centre.
Question 2 of 5
A section has Ix = 3.0 × 10⁶ mm⁴ and Iy = 1.2 × 10⁶ mm⁴ about perpendicular axes through its centroid. What is its polar moment about the centroid?
Question 3 of 5
A plate is 80 mm wide and 30 mm tall. What is its polar moment of inertia about one corner?
Question 4 of 5
A solid shaft has J = 251,327 mm⁴ and outer radius 20 mm. What is the maximum shear stress when it carries a torque of 300 N·m?
Question 5 of 5
Why should τ = Tρ/J not be used for a bar with a rectangular cross-section?
