Statics › Section I · Friction › Topic I.3

Wedges

A wedge is the simplest machine there is: a tapered block that turns a modest push into a large sideways force. Whether it lifts a machine, splits a log or stays jammed in a doorway depends on friction at every face, and this topic shows how to account for all of it.

What a wedge does

A wedge is a tapered body that works as a moving inclined plane. Driven forward a long way, it pushes the bodies it touches apart a short way, so a small input force can produce a large output force. The narrower the taper, the larger that gain. Wedges are used in two quite different ways. Low-friction wedges are machines for doing work: a log splitter rams a log against a fixed steel wedge, and a thin wedge driven under a heavy machine raises it slightly for levelling. High-friction wedges are for holding: a doorstop, or a pair of folding wedges hammered toward each other to tighten timber shoring. Both kinds are analysed in exactly the same way.

Free-body diagrams for wedges

Draw a separate free-body diagram for the wedge and for each body it touches. At every contact surface, show two forces. The normal force is perpendicular to the surface and pushes into the body it acts on, because contacts can only press, never pull. The friction force lies along the surface and opposes the relative slip at that contact. Where a force passes from one diagram to the next, draw it equal and opposite, as an action-reaction pair. Wedges are usually light compared with the loads, so their weight is neglected. The angled faces mean that normal and friction forces must be resolved into components, using the wedge angle \(\theta\) and right-angle trigonometry.

Getting friction directions right

In most statics problems you can guess the direction of an unknown force and let a negative answer correct you. At impending motion, friction cannot be handled that way, because writing \(F = \mu_s N\) already fixes its size, and a wrong direction gives a wrong answer. Instead, picture the motion about to happen. If the wedge is about to move right, the floor's friction on the wedge points left. For the body on top, ask how it moves relative to the wedge face, not relative to the ground: a body rising straight up while the wedge slides under it is slipping along the face toward the thick end, so friction on it points along the face toward the thin end.

The frictionless benchmark

Take a block of weight \(W\) that can only move vertically, resting on a wedge whose top face is at angle \(\theta\), with every contact smooth. The wedge face pushes on the block with a normal force tilted \(\theta\) from vertical. Its vertical component carries the weight, \(N\cos\theta = W\), and its horizontal component, \(N\sin\theta\), is what the push must supply, since the wedge feels the equal and opposite force. So

P = W\tan\theta

For a 10° wedge, \(P = 0.176W\): a push of under a fifth of the load. Friction adds a large amount to this, which is why a real wedge can need several times the frictionless push.

Worked example: lifting a machine

A 400 kg machine must be raised slightly. Its right side bears against a vertical steel column, and it rests on a sloped pad on top of a light 15° wedge. The wedge's bottom face is on the level floor, its top face rises toward the left, and it is driven to the right, thin end first. Take \(\mu_s = 0.20\) at all three contacts, and call the normal forces \(N_c\) at the column, \(N_2\) between wedge and machine, and \(N_1\) at the floor. 1. Machine: \(W = 3924\) N, rising, so column friction acts down and wedge friction acts along the face toward the thin end. 2. Machine, horizontally and then vertically:

N_c = N_2(\sin 15^\circ + 0.20\cos 15^\circ) = 0.452N_2
N_2(\cos 15^\circ - 0.20\sin 15^\circ) - 0.20N_c = W

3. Solving, \(N_2 = 4764\) N and \(N_c = 2153\) N. 4. Wedge, vertically: \(N_1 = 0.914N_2 = 4355\) N. 5. Wedge, horizontally: \(P = N_c + 0.20N_1 = 2153 + 871 = 3024\) N.

Reading the lifting result

The push needed is about 3.02 kN. With every surface smooth, the benchmark gives \(3924\tan 15^\circ = 1051\) N, so friction roughly triples the effort, and only about 35% of the work done by the push goes into raising the machine. Step 5 used a shortcut: the wedge's horizontal equation contains the same combination of \(N_2\) terms as the machine's, so it reduces to the column force plus the floor friction. A useful check on any wedge answer is the direction of each friction force. Here all three oppose the lift, so the answer must exceed the frictionless value, and it does.

Self-locking wedges

Remove the push, and will the wedge stay? With no push, a light wedge is acted on only by the two contact resultants on its faces, so it is a two-force body: those resultants must be equal, opposite and collinear. Each can tilt at most \(\phi_s\) from its own normal, and the two face normals fall short of pointing in exactly opposite directions by the wedge's included angle \(\theta\). The forces can line up only if the two tilts together make up \(\theta\), so a wedge with the same coefficient on both faces stays put when

\theta \le 2\phi_s

A narrow wedge is therefore more likely to hold. For a symmetric splitting wedge with half-angle \(\alpha\), the condition becomes \(\alpha \le \phi_s\).

Worked example: withdrawing the wedge

Will the 15° wedge under the machine stay in place, and what horizontal force removes it? 1. Self-locking test: \(\phi_s = \tan^{-1} 0.20 = 11.3^\circ\), so \(2\phi_s = 22.6^\circ\), more than 15°. The wedge holds. 2. For withdrawal, the machine is about to move down and the wedge left, so every friction force reverses. 3. Machine:

N_c = N_2(\sin 15^\circ - 0.20\cos 15^\circ) = 0.0656N_2
N_2(\cos 15^\circ + 0.20\sin 15^\circ) + 0.20N_c = 3924

so \(N_2 = 3807\) N and \(N_c = 250\) N. 4. Wedge, vertically: \(N_1 = 1.018N_2 = 3874\) N. 5. Wedge, horizontally:

P' = N_2(0.20\cos 15^\circ - \sin 15^\circ) + 0.20N_1

which is \(-250 + 775 = 525\) N. A positive pull is needed, which agrees with step 1. The wedge stays at rest for any force between a 525 N pull and a 3024 N push.

Common mistakes to avoid

First, drawing friction on the top body relative to the ground instead of relative to the wedge face it slides on. Second, forgetting that action-reaction pairs must appear equal and opposite on neighbouring diagrams. Third, reusing the lifting friction directions for withdrawal; every one reverses. Fourth, resolving the face forces with sine and cosine swapped. Check with \(\theta = 0\), where the face becomes flat and the normal force must be vertical. Fifth, judging self-locking from the wedge angle alone; it depends on the angle compared with \(2\phi_s\).

Key takeaways

A wedge is a moving inclined plane that turns a small push into a large force; a narrow taper gives more gain. Draw a diagram for each body, with normal forces pressing into each body and friction opposing the relative slip at each face, passed between diagrams as equal and opposite pairs. Friction directions must be decided before solving. With smooth contacts, P = W tan θ; friction can make the real push several times larger. A wedge with the same μs on both faces is self-locking when its included angle is at most 2φs, and removing it then needs a pull, found by reversing every friction force.

Flashcards

Flashcard

Wedge

A tapered body acting as a moving inclined plane

A small push gives a large sideways force.

Test your understanding

Question 1 of 5

A load of 5,000 N, guided so it can only move vertically, rests on a 10° wedge. Every contact is smooth. What horizontal push on the wedge holds the load in equilibrium?

Question 2 of 5

A light wedge with an included angle of 10° is driven into a gap, and μs = 0.10 on both faces. What happens when the driving force is removed?

Question 3 of 5

A wedge resting on a level floor is about to be driven to the right under a load. Which way does the floor's friction force on the wedge point?

Question 4 of 5

You have solved for the push that drives a wedge in under a load. To find the force that pulls it back out, what must change in the free-body diagrams?

Question 5 of 5

A symmetric splitting wedge has an included angle of 16° and the same μs on both faces. What is the smallest μs that keeps it stuck in a log?

← Previous topicNext topic →